Search results

  1. Scott06

    No start after engine install. Need Help!!!

    Go through the rest of the TB troubleshooting guide.
  2. Scott06

    No start after engine install. Need Help!!!

    The TB troubleshooting guide starts with verifying the tach wire isn’t shorted to ground …
  3. Scott06

    Hole shot

    So I….
  4. Scott06

    No start after engine install. Need Help!!!

    Disconnect the tach wire (grey) at negative post on the coil. This will remove any chance the tach is killing the spark you can also disconnect it and check for continuity to ground with a volt meter. woukd agree battery and connections both positive and negative are suspect given the voltage drop
  5. Scott06

    Engine hour meter clicks with ignition on, but engine not running

    On an analog engine that is the only way to know it is running ( or should be…) power to ignition circuit.
  6. Scott06

    No start after engine install. Need Help!!!

    the oil pressure alarm doesn’t interrupt the ignition. It just makes the buzzer go off when below 4 or 7 psi.
  7. Scott06

    No start after engine install. Need Help!!!

    Wi willing to bet during cranking you are loosing voltage, start with positive battery and ground cables.ther are 2-3 at the back on flywheel cover Measure with a volt meter on positive terminal of coil while cranking should stay close to 12. Then go through the thunderbolt ignition...
  8. Scott06

    outdrive stuck

    That’s the point with a press you wont damage the splines unless you are chit faced…a bar on either side of the bearing or use bearing separator , press down on the center of the shaft with a pice of round stock or socket
  9. Scott06

    outdrive stuck

    Yeah I put mine on wheels but fervently stub my toes on it. I bought mine for rebuilding the suspension and changing rear gears on my gto. Was right there when rebuilding jet pump on the seadoo and doing seals and bearings on my outdrive. For all the work you do it’s worth it.
  10. Scott06

    outdrive stuck

    If you were changing the u joints yes take the yoke off put it in a $100 harbor freight press and it will come off with out damaging anything The press is well worth the investment
  11. Scott06

    Intermediate shift shaft play?

    It isn’t the tightest fit when new but based on your comments replace the bushing and seal likely is needed based on your comments
  12. Scott06

    Learning to wake board at 48. What am I doing wrong?

    I also learned to wakeboard in my mid 40 s Could be a couple things would try switching which foot is forward as suggested Also I have found leaving the board at a 45 degree angle ( for me to the left) vs perpendicular makes it easier to get up. This may not be correct but then as I get up...
  13. Scott06

    outdrive stuck

    Yes you can cut it off just take care on the inner race not to cut into drive shaft
  14. Scott06

    2024 wake pro 230

    would Really defeat one of the prime benefits of having a closed cooling system if you had to change out the AF
  15. Scott06

    New SeaRay owner (Sundancer 250) with some basic questions

    There is a forum called club sea ray you may find more specific info to your model there. There are a few guys on the site that work at sea ray dealers so know all the issues https://www.clubsearay.com/
  16. Scott06

    93 mercruiser 4.3 alpha one gen 2 fuel problem (I think)

    Yes it had a heated choke newer edlebrocks and some of the later webbers used electric chokes.
  17. Scott06

    93 mercruiser 4.3 alpha one gen 2 fuel problem (I think)

    It is an oem merc webber. that’s the choke pull off which uses vacuum to operate
  18. Scott06

    Water in Oil

    Yes propeller shaft until locked into gear will have in and out play. this is why you always do a water test.… tryto get it running soon put oil in affected cylinders , until you get it running. Once running get some inexpensive oil and keep changing it until it runs clean. You only need 3 qts...
  19. Scott06

    outdrive stuck

    Take your time , you will get it off. Given vibration and noise bet you find rusty u joints and gimbal seized to driveshaft.
  20. Scott06

    Alpha One Gen 2 Drive Shaft

    If yoke is grooved yes sleeve it or replace just the yoke
Top