Search results

  1. Bondo

    Bellows Installation

    Ayuh,.... follow the manual, as explained in there, the sequence falls into place,....
  2. Bondo

    Trim cylinder hose replacement

    Yes,..... Atf, or light weight hyd. oil,....
  3. Bondo

    Cam for SBC 350 early model non roller

    Ayuh,..... A high zinc content,.....
  4. Bondo

    Cam for SBC 350 early model non roller

    Ayuh,..... Welcome Aboard,...... You want a cam that builds power up to 5,000 rpms,..... I believe yer choice of intake is misguided, as it's for higher rpms,.... The carb is bigger than ideal,.... 'n yer gear ratio is to low,... should be 1.50:1,.... What's the static compression...
  5. Bondo

    Mercruiser 4.3 Prop Question

    Ayuh,...... Welcome Aboard,.. Yes, a smaller prop will bring the rpms up,... Are you sure the motor is putting out the power it should be,..?? What's the back story,..?? has it ever run the right rpms,..??
  6. Bondo

    Trim cylinder hose replacement

    Ayuh,...... I've never rebuilt a set of rams as new as yer's, so I can't say for sure,..... Personally, I'd clean up what you got, replace the cut lines, 'n run it till you find the actual cause,..... Something not discussed is I wonder whether the water didn't come from the hyd. tank...
  7. Bondo

    Trim cylinder hose replacement

    Ayuh,..... It doesn't take much, yer just trying to seal the ssteel threads from corroding into the aluminum housing,....
  8. Bondo

    Trim cylinder hose replacement

    Ayuh,...... Welcome Aboard,....... Quicksilver Perfect Seal, aka: form-a-gasket non-hardening liquid, #3,..... I use it on pretty much every threaded fastener that I might want to take apart someday,.....
  9. Bondo

    Mercruiser 5.0 Thunderbolt 5 ignition

    Ayuh,.... Welcome Aboard,..... Cross check yer tach, with a known good shop tach to verify that it's accurate,.... I suspect it's not,....
  10. Bondo

    Gas station floods

    Ayuh,...... Tank vents are usually over by the building, about 10' high,....
  11. Bondo

    Ranger 12' cracks?

    Ayuh,..... Welcome Aboard,.... That's what I would do, ^,.....
  12. Bondo

    Checking out a 24' Four Winns with a 5.7 Volvo Penta motor

    Ayuh,..... If the Efi dies, you swap to a 4bbl. carb,..... If the ignition dies, you swap in a Delco voyager system,....
  13. Bondo

    Checking out a 24' Four Winns with a 5.7 Volvo Penta motor

    Ayuh,...... The 350 Merc, 'n the 350 Volvo are the exact same Chevy long block motors,..... They're just dressed with Merc, or Volvo accessories, induction, ignition, etc....... You don't mention which Volvo drive, so no comment there,....
  14. Bondo

    Another Winterization Thread!

    Ayuh,....... Donno, don't know you that well,....... Yet,..... I've lived in the far north all my life, 'n have always known that, Air Don't Freeze,...... What you propose is entirely doable, No problem,....
  15. Bondo

    my boat won’t sit on the front bottom roller

    Ayuh,...... You should be able to extend it with a couple pieces of flat stock of the appropriate size,.... Post a picture of what you've got,....
  16. Bondo

    my boat won’t sit on the front bottom roller

    Ayuh,..... Welcome Aboard,..... On most trailers, they're adjustable, so adjust yer's to fit better,....
  17. Bondo

    Drive Lube Replacement

    Ayuh,..... Welcome Aboard,...... Yes, no draining the lube for the shift cable swap,.....
  18. Bondo

    5.7 coil issues

    Ayuh,...... Welcome Aboard,..... Please explain,..??......
  19. Bondo

    Wake boat fuel supply issues

    Ayuh,...... I've done alota boat fuel tanks, 'n have never run acrost anything as convoluted as you explain,.....
  20. Bondo

    Seaswirl 190SE

    Ayuh,..... Welcome Aboard,....... It Could be alota things,.... Ya start yer diagnosis with the most likely, easier things to check,..... If you don't find joy, you move on to other possibilities,.....
Top