Search results

  1. tpenfield

    ECM Swap ? Plug and play ???

    Use PMs to the OP to discuss personal transactions further. :)
  2. tpenfield

    1990 Bayliner 2651 resto

    A judgement call in the fuel tank as to if it can be saved. Check to see if there is a certification label with the material and thickness. I would not go with any pits that are deeper than 1/3 the thickness. Also see if you can get a glimpse inside the tank for any internal corrosion/pits...
  3. tpenfield

    1975 Merc 7.5 thunderbolt hard starting

    My 1969 7.5 Mercury is a '5 pull' start, but it always starts. I did at one point have to fully disassemble the carburetor (Tillotson carb IIRC) and do a re-build kit on it. Also, assuming you have done the primer bulb thing to get fuel up to the carb. I usually have to start the engine on...
  4. tpenfield

    Mercruiser 6.2 cracked engine block from cold

    Not sure what you are asking. This information (part & price) came from online. Where are you located?
  5. tpenfield

    Old 9.9 Mercury looking for year made. 0B390028

    +1 for 1989 model year. Looks like there is a 'tiller shift' and a 'side shift' version of the motor. So, assuming to are looking to take a 'side shift' and make it a 'tiller shift' (and throttle). It might be easier to get a tiller version of the same/similar motor. :unsure:
  6. tpenfield

    Mercruiser 6.2 cracked engine block from cold

    6.2L (377 Cu In) V8 Mercury 6.2 MPI 300 HP [2A530776 & Up] - Cat.# 90-8M0124044 The cylinder block is listed as not stocked separately. There is a long block P/N . . . 8M0114814. Lists for about $11,000 USD
  7. tpenfield

    Trouble getting tags for trailer

    I'd double check that with the WV website. Usually, if you have the previous title, there is no need for previous registration.
  8. tpenfield

    Engine Temp

    Usually, it is a restriction in the flow of water that causes these situations. I would check any/all oil coolers along the intake path for debris that might be restricting the flow. You can test the thermostat with a pot of water & thermometer on the stove to see at what temperature it opens
  9. tpenfield

    Hi guys! Any cause for concern with these cracks ? 2008 moomba mobius xlv

    Those would have me thinking twice. The boat is probably fine. Seem to be stress cracks. Maybe better to find a boat that is not so stressed :LOL:.
  10. tpenfield

    My boat is being a boat . . .

    Quick Update . . . A 3.9 foot tide will have to do as the 4+ foot tides are still another week away. I put in for my 'wide load' permit. The weather for next week has decided to go sour, but it looks like Wednesday June 7th will be OK to launch.
  11. tpenfield

    72 glastron/General boat question..

    The lower is the typical bilge drain. Generally threaded plugs are best, but if the hole has no threads then an expanding plug will have to do. The higher 'hole' would be a transom well drain. It should be above the waterline when the boat is at rest. That one should stay open so any water...
  12. tpenfield

    1969 Glasspar 17' Citation(?)

    Looks like fiberglass stringers. May be foam cored. . Yes, it is a good idea to add the foam back in.
  13. tpenfield

    Mercruiser 6.2 cracked engine block from cold

    Yes, if it is the new version of the 6.2, which came out about in the year 2015, the engine is all Mercruiser and not a GM-based engine. Got a serial number to verify the engine? Depending on where you are located, a new engine will be a bit pricey...
  14. tpenfield

    Volvo Penta 2015 codes 697, 698, 699

    No, no . . . the two best days are the day you buy it and the day you sell it! :ROFLMAO:
  15. tpenfield

    Stamas 244 freedom

    Some information, but not much . . . http://boatspecs.iboats.com/Stamas_Yachts__Freedom__244_Freedom/bp/43br1465s4882m31342 Stamas is generally considered a solid ocean-going boat, tending to favor the fishing crowd, although 244 would be on the smaller end of the scale. I believe there is a...
  16. tpenfield

    Curious on selling price

    Your boat? Planning on selling? Do this . . . Check NADA (JDPower) for their price estimate (they are typically low on older boats.) Check boat listings for same/similar boats. Subscribe to BUCvalue.com and check their estimate. Those 3 data points should get you to a price range. Combine...
  17. tpenfield

    4.5L Water in Oil, Bent Valve, O2 Hydrolock

    The only raw water cooled engine that I ran in salt (100% of its use) lasted about 20 years and then it was toast. (with jelly) :LOL:
  18. tpenfield

    Artificial Intelligence parts finder

    Perhaps it was ChatGPT ?
  19. tpenfield

    suzuki dt 200 over rev limiter restricts top end

    Please don't post to old/dormant threads as per the forum rules. The OP has not been on the forums since 2011 and unlikely to respond. It is best to post your own thread with your relevant information. Closed.
  20. tpenfield

    Bravo 3 can you change gear oil line without removing lower unit?

    Welcome to iBoats. . . First word of caution . . . don't take off the lower unit. (you'll get a big surprise). o_O As @04fxdwgi25 explained, the oil line is very tight on the starboard side of the bell housing. even with the drive removed and the bell housing detached, it is a tough go.
Top