Search results

  1. Scott06

    Any Transom experts here. I have a Transom Rebuilding Question.

    this is the closest I could find for transom specs - is for a gen 2 which will be the same cut out I believe for your gen 1...
  2. Scott06

    Easiest Conversion

    there is also one on ebay somewhat reasonably priced...
  3. Scott06

    Assembling a 4.3 MerCruiser v6 - Parts check needed

    have you measured the bores? you are practicing the age old art of turd polishing....
  4. Scott06

    Marine Insurance

    I also have my boat with Progressive. Have yet to see any huge premium raises in years. Unfortunately if you don't regularly shop it around you screw yourself by being loyal. Biggest rip off I have seen lately is homeowners. Replacement cost drive those up
  5. Scott06

    Any Transom experts here. I have a Transom Rebuilding Question.

    In a word No ... use the merc thickness spec otherwise transom plate will not fit on and driveshaft will go that much less in coupler. 2 x 3/4 ply plus fiber glass on either side is fine as long as it is not rotted
  6. Scott06

    MerCruiser 6.2L s/n# 0W032927 Fuel system question Need both fuel pump & filter part numbers.

    Parts breakdown is here https://www.marineengine.com/parts/mercury_marine_parts/sn/oW032927 In 4 th and 5 th pics The item with the two red capped wires is a fuel shutoff valve that was installed by boat manufacturer. My Sea Ray has one that is connected into the engine harness to open when...
  7. Scott06

    5.0xl/V8 mer. Where do I start?

    Look at some of the resto threads on here. Floor usually rots after the stringers and transom which are the structure of the hull. I would be drilling 1/4" holes down low in stringers and transom also in ski locker. Willing to bet they come out mush. Do this before investing any money getting...
  8. Scott06

    Replacing lift cyl power trim hose,how much heat to use?

    I know but how do you quantify that??? Mapp or propane is fine. Start with a little try to get it off, add more if needed. Aluminum doesn't take much to expand. As mentioned if you are concerned try a heat gun first. Probably 150-180 F will do it? This is just based off of using a bearing to...
  9. Scott06

    1990 OMC 4.3l Cobra ASKING FOR ADVICE

    I have sold similar items on Ebay and also craigslist. Never did FB Market place but could also sell there. Would make sure it is running and can demonstrate oil pressure and compression for buyer. A lot of times you seem them listed still in boat will ship a week after sale to remove it. You...
  10. Scott06

    Tire Recommendation, Japanese Sedan

    I had play in a CV joint on my mother in laws Civic , would clack when going from coast to acceleration, jacked it up no play in suspension, if you held the center of the axle and turned the wheel it would clack, reversing wheel direction made it happen ever time. Other side had no noise, axle...
  11. Scott06

    Assembling a 4.3 MerCruiser v6 - Parts check needed

    I would call the seller and say it binds up should not bind up at all. If you put it on a credit card you can always dispute the charge. Bottom line if it binds up something is wrong machining wise. Had an issue one time where the big ends of the rods when resized were at an angle to the rod...
  12. Scott06

    Replacing lift cyl power trim hose,how much heat to use?

    You may need some good heat and some Kroil or other goo penetrating oil applied days before hand. you also can cut the line to get a box wrench on it
  13. Scott06

    Bad hesitation at 1200 rpm

    Do you get a good accelerator pump shot? Would be thinking the of idle or transition circuit may be clogged. Given the age might be worth rebuilding setting float level etc Have you tried adjusting idle mix screw out (richer) to see if it smooths this out? Willing to bet at factory they were...
  14. Scott06

    Kicker on a CC?

    If you go in remote places sure it makes sense for back up. Im not sure of fuel or lowering the main engine hours it will pay for itself. Downside is it will clutter the stern some and you need to be able to pull it up or tilt up when at speed. Back in the day lake trout fishing with my...
  15. Scott06

    Any Transom experts here. I have a Transom Rebuilding Question.

    Agree with others - have never seen a fiberglass gasket. Wonder if it was cloth that resin never kicked off. Read the resto forum to see what others have done. Certainly given how you need to bond and sandwich the transom wood to the outer fiberglass there is certainly the opportunity for it to...
  16. Scott06

    Assembling a 4.3 MerCruiser v6 - Parts check needed

    Send the whole thing back , it’s not a matter of swapping cranks. Something is machined wrong if it binds probably thrust surface .
  17. Scott06

    Assembling a 4.3 MerCruiser v6 - Parts check needed

    that sounds like a hot air choke, as mentioned above you would need to convert to electric which is no big deal
  18. Scott06

    4.3l mercruiser no start when hot

    if it is shooting gas in when hot then would think you must be loosing spark somewhere otherwise it would at least cough
  19. Scott06

    Need better hole shot

    its the prop version of one footitis....
  20. Scott06

    Any Transom experts here. I have a Transom Rebuilding Question.

    if the lag screws didnt jank out when you pulled the motor that is a good sign
Top