Search results

  1. R

    96 Evinrude 50 Cutting Out

    Likely no one could swap it into a motor that does not use that part.
  2. R

    Johnson 40hp 2005 link and idle adjustments

    The primer valve is only used for cold starts.-----When motor is running it does NOTHING.
  3. R

    96 Evinrude 50 Cutting Out

    The 2 wire sensor has been listed as NLA for quite a few years now.
  4. R

    Johnson 40hp 2005 link and idle adjustments

    ???---What---the primer valve is CLOSED when engine is running.----It does NOTHING.----The electric primer is only used for starting a cold motor.
  5. R

    Johnson 40hp 2005 link and idle adjustments

    But there are some idle circuits that are DIFFERENT on outboards.
  6. R

    90 evinrude wont idle or rev in water but it didn't on muffs

    Motor likely suffered from a broken piston ring.----From where I sit I would say rebuild time with 4 new O/S pistons.------A very common failure I think.
  7. R

    96 Evinrude 50 Cutting Out

    Reving it up on the trailer means nothing ---Waste of time..----Even in gear on the trailer is still neutral !!!------A 2 cylinder motor.----Sounds like it is running on 1 cylinder.----The simple testing needs to be done.-----No spark?---Poor compression ?----No crankcase compression.-----Timer...
  8. R

    OMC Cobra Lower unit replacement

    Try-----kingspropeller ----In Ontario.----Might find a used unit there.
  9. R

    1986 merc 40hp 4cyl

    Lots of new /used parts available.----As stated marketed for many years.
  10. R

    how to remove water pump base 1978 1400 EZ Shift?

    Jerking up on the driveshaft won't help.
  11. R

    Aluminum Boat Transom Knee

    I would just use tubing and angle.-----Use 2 pieces of tubing for each knee and 3/16" angle to rivet to bottom and bolt to transom.
  12. R

    Aluminum Boat Transom Knee

    I would use 2X3" aluminum tubing to fabricate a structure or maybe 2 knees.----Along with some welding.-----Aluminum sheet does not always like being bent.
  13. R

    tell tale channel clogged 1966 Merc 500

    You might find a pipe plug near spark plugs.----A water pressure gauge could be fitted.----And install a new impeller every 5 years.
  14. R

    90 evinrude wont idle or rev in water but it didn't on muffs

    Well ---I know it is a V-4.----But from 1995 to 1998 there were 2 totally different V-4 mofels !
  15. R

    Johnson 9.9 j10rcse repair/ restoration

    The fuel pump is easy to repair and would likely just need a new diaphragm.
  16. R

    1986 merc 40hp 4cyl

    Total tear down is needed.
  17. R

    90 evinrude wont idle or rev in water but it didn't on muffs

    What Is the model # or is it a crossflow or 60 degree looper ?
  18. R

    96 Evinrude 50 Cutting Out

    Where did you look on the parts break down.-----We need to know if it is a 2 cylinder motor or a 3 cylinder motor.----Model # is ?
  19. R

    1986 Mercury 90 hp 6 cylinder only running on #2, 4 and 6 cylinders

    Sounds like a bad switch box.-----There are of them.----You could test by swapping them and see if there is no spark on 1 , 3 and 5 and spark on 2 , 4 and 6.
  20. R

    96 Evinrude 50 Cutting Out

    Salty are you sure this motor has a 2 wire heat sensor , along with limp mode ?
Top