Search results

  1. R

    Fast idle/start

    Try adjusting the black plastic thing ( trunnion ) on the cable.---Slight preload against the idle stop screw.
  2. R

    1997 Evinrude e50tsleus

    It is the correct dimension.---Set it in neutral ?--How did it shift for you a month ago ?
  3. R

    1957 Johnson Rd-19 35hp questions

    Sorry----Too far away for quick help.
  4. R

    1957 Johnson Rd-19 35hp questions

    Your location ?
  5. R

    Fast idle/start

    Lever should bring it back against the idle stop.----Tried adjusting throttle cable?
  6. R

    1972 Evinrude 40 outboard no spark?

    Repeat-----There is only one wire going to that switch !---And that switch grounds internally.-----It is NOT the kill switch.----It prevents cranking if throttle is open too far. !----Remove sparkplugs and use an open air spark tester to test for spark.----Those inline spark testers do not...
  7. R

    2000 - 225 Evinrude Fitch EMM Question

    Replaced the water pump impeller ?
  8. R

    1972 Evinrude 40 outboard no spark?

    One with 2 blades sticking out should have 1 ( white ? ) wire.----It is the safety switch to prevent cranking with too much throttle open.----Other is a vacuum switch to prevent motor " run a way " under certain conditions.----Cuts out spark to one cylinder.---Open the big black plug on...
  9. R

    Evinrude 10HP 1964 motor needs skeg repair or replacement.

    Your location ?---For just the bottom half.------Any year Johnson / Evinrude 10 HP from 1958 to 1963.-----Any year 5.5 / 6 HP from 1955 to 1979 model.-----And of course the 9.5 from 64 to 1973 use that skeg.-----I know where to find lots of them.
  10. R

    1989 Evinrude 150xp Temp Gauge, Starboard Temp Switch, Fast Idle & Forward to Neutral Shifting

    ^^^^ Agreed.
  11. R

    Evinrude 10HP 1964 motor needs skeg repair or replacement.

    Hopefully next year I can get out to Alberta again.----Saw the grandson at the----" Canada Wide Science Fair "---- in Ottawa.-----He was a finalist there with his project.----An 8 hr drive for me is easier than 4 days.
  12. R

    Evinrude 10HP 1964 motor needs skeg repair or replacement.

    No it will not.----The skeg from a 56 FD 10 is a bigger unit like the 18 HP.
  13. R

    Toyota/Lexus Timing Belt Change Thoughts

    Most Toyota engines are " clearance " engines.-----Lost the belt on an 84 Supra inline 6.----Put a new one on and it ran like normal again.
  14. R

    Evinrude 10HP 1964 motor needs skeg repair or replacement.

    Johnson marketed a 10 in 49----Evinrude started that in 56 with a 10 HP.-----Not all models were the same between the 2 divisions in the early years.-----Up to 57 the 10 HP used the 18 HP gearcase.
  15. R

    Evinrude 10HP 1964 motor needs skeg repair or replacement.

    Evinrude 10 HP was from 56 to 63 model years.
  16. R

    Johnson TN28 no low-speed fuel

    Rotary valve is just holes drilled in the crankshaft.
  17. R

    50hp Johnson 2 stroke prop

    Try a 21" pitch.
  18. R

    1957 Johnson Rd-19 35hp questions

    Short driveshaft should be easy to find.
  19. R

    Johnson TN28 no low-speed fuel

    Have you adjusted the low speed mixture screw that feeds the rotary valve ?
  20. R

    Evinrude 10HP 1964 motor needs skeg repair or replacement.

    The upper and lower half of the gearcase are machined as a unit .----Considered to be one piece.----You may get lucky just replacing the bottom part.-----Was it cracked due to water freezing ?-----Take it apart to inspect gears and bushing above pinion gear.----This will be costly if you need a...
Top