Search results

  1. flashback

    Blower fan and Bilge is NOT working. Help

    That's where the breaker is on my 95 searay. right under the switch.
  2. flashback

    Never underestimate the power of the mechanical fuel pump

    Did you figure out what caused the increase?
  3. flashback

    Screw Hole Repair / Below Water Line

    If there's no wood involved your patch will probably last forever. Marine tex might have been a better choice if your hull is white.
  4. flashback

    Is talormade curved windshield really glass?

    I used a razor blade and some windex and it worked out fine. The windshield is indeed tempered safety glass and it's nice and smooth now..
  5. flashback

    Stuck Valve/Cracked Head/Cracked Block

    If your engine is like an old 350 I had, rocker studs are press fit so be sure the stud didn't slip.
  6. flashback

    mercrusier 350 MAG MPI coupler problem

    I had the same question a few weeks ago, the splines don't go the entire length of the coupler.
  7. flashback

    Fuel Pump Diaphragm Rupture Hose Type?

    A couple of months ago I converted to an electric fuel pump and removed that hose and if I remember it connected to a small brass fitting that is pressed into the carb body just below the top edge of the carb.
  8. flashback

    Is talormade curved windshield really glass?

    Ha, we must have met at some time, you know me!
  9. flashback

    Is talormade curved windshield really glass?

    It's the 95 sea ray. I just didn't want to take a razor blade to it if it's not glass. Most likely the paint is 2 part epoxy picked up in a boat yard somewhere. It's not too bad but you can feel it, I'll pick an inconspicuous spot and experiment. Probably try some spirits first and maybe some...
  10. flashback

    Is talormade curved windshield really glass?

    They seem to advertise it as glass, but before I try to clean off some paint overspray that it gathered sometime in the past it would be good to know what its made of.
  11. flashback

    Outdrive gasket pushing out

    I can relate to that, I recently replaced the SS wire rope on a boat lift and thought I could re-use the old clips. Wrong! When I tried to loosen them every one locked up. Had to get new clips..I'll know next time..LOL
  12. flashback

    Steering maintenance

    If I were doing the evaluation service points would raise the score! My boy has an MTD riding mower and it needs a blade spindle,why... No grease fitting for the bearing. My truck has a noisy wheel bearing, why... I can't re-pack it. But the spark plugs sure do last.
  13. flashback

    Steering maintenance

    My only experience of "feedback" has been with PA systems and guitar amps. thanks for clearing that up for me. Mainly I am looking for any lubing or adjustments that might be available Like greasing the rack mechanism or cable and adjustment procedures if any. I don't have a manual on Teleflex...
  14. flashback

    Steering maintenance

    I was afraid you'd say that! LOL. I didn't take anything apart but I took the patch off the transom plate and the tiller, swivel pin and bushing were tight as were the pinch bolts on the ring. Which reminds me, I recall on my old MC1 drive there was a grease fitting for the bushings. I wonder...
  15. flashback

    Steering maintenance

    Apologies, guys, I just realized that my signature doesn't show up on the phone. Yep it's the 95 searay 220. This boat wanders like a gypsy at slow speed, it's heavy and obstinate! What concerns me is the play while on plane. I can turn the wheel 2 inches either direction before I get a...
  16. flashback

    Steering maintenance

    I would like to reduce the slop in the steering system so I read up on it in the manual and came across one of the many Merc "IMPORTANT" boxes..."slight feed back could be encountered if cable guide tube flat surfaces are not positioned vertically." Mine are horizontal. I don't know what slight...
  17. flashback

    Power Steering Pump Mounting?

    And another hope it helps.
  18. flashback

    Time to reassemble

    Guess that why they call it a shake down cruise! In my case the shoe fit ok. It shifted really well at first, I ran it thru the gears several times in open water and it shifted fine, then coming back in I chunked it into neutral and then hit reverse for braking purposes and found I had no...
  19. flashback

    Time to reassemble

    When I launched last week I had a damaged prop and just wanted to get it to the dock. Since then I put a new prop on and yesterday went out for a proper ride for about 3 hours. The SEI drive has a distinct jet engine sound which I understand may go away once it is broke in as I know the owner...
  20. flashback

    Lower Shift Cable Adjustment - Am I doing it right?

    You have to establish a base point to work from, forward gear is a good place to start. The detent on the remote is not a place to measure from, that's why the slot is there, to adjust for slop in the remote.
Top