Search results

  1. jerryjerry05

    Hyd. line location.

    This should be listed under "Old Dog, New Tricks" Was trying to help on a hydraulic pump problem. Looked up the parts diagrams for the motor, year and model. Saw that the diagram had the lines marked and the corresponding holes in the pump marked. Might help someone??
  2. jerryjerry05

    Fouling 1 plug

    About a 1982 50hp. 4 cy. Ser#5951619 Has good comp on all 4 about 150-155 Good spark on all 4 ​I can change the plugs and the problem stays on #3 The reeds are ok. The carbs spotless. The fuel pump diaphragms both OK. Starts and runs poorly. The 3rd cyl. from the top carbons up real bad after a...
  3. jerryjerry05

    Pack

    Working on 82 50 hp 4cyl. Tested the stator.It's bad. Replaced with a good one, tested ok. I have a DVA Still no spark. Could it be possible that the stator and pack went bad at the same time??????? Found test procedures from CDI for the pack, gonna see if it's bad? Thanks,Jerry
  4. jerryjerry05

    Helping at the ramp.

    Was waiting for a truck to back down the ramp and load their boat. ​The driver(woman) was not having a good day. One time the trailer went left the next right. Just couldn't get it right. It was a 2 car ramp and she was holding up both lanes. I wasn't gonna put in next to her and have...
  5. jerryjerry05

    Setting idle on 15Jhnson

    1988 15hpJohnson J15rccs. How to set the idle ? It runs and runs good. Just want to make sure I've got the idle set right. I have a tiny tach and need the specs on idle etc?? TY
  6. jerryjerry05

    Pull cord mechanism binding

    1988 15hp Johnson J15RCCS. I removed the pull starter to work on the carb. Now when I reinstall and tighten down the bolt it binds when pulling if I tightened all the way. I even tried a different pull starter. Same,same. Any pics of the unit? Is there a washer/ spacer on the bottom of...
  7. jerryjerry05

    2hp 1983

    Trying to remove the prop. I've got the cotter pin out and don't wanna break anything. The prop is 25$ and don't need to spend anymore than I have to. Thanks.
  8. jerryjerry05

    2hp adjustment

    Working on the neighborhood kids 2hp Evenrude. It has 2 adjustment screws. ​Mod E2RCTD E0165053 The top is slow speed and bottom is high speed. Any links on adjusting? Any help would be appreciated.
  9. jerryjerry05

    Earlier Cobra Shifting Problems.

    The Early Cobra's up until they went to the Volvo shift mechanism. The Shift assy. wasn't the​ best but you need to work with what you have. The cable can be the problem but lots of times it's the bellcrank. A lot of the shift problems can be helped with a bit of cleaning and a shot...
  10. jerryjerry05

    Decal

    H​ave a 1998 225 Johnson The decals are faded and need to be replaced. Any places that make them or sell??\\ Thanks,J
  11. jerryjerry05

    Yamaha 15hp prop?

    Have a1995 Yam 15hp. The prop has B-2239 stamped into it. Looked on the Parts pages and can't find any thing to compare. Any idea? It's my nephew's Whaler and he beats the prop up pretty good. Before he destroys it I'm looking for a replacement. Thanks for any help...
  12. jerryjerry05

    98/75 hp Flywheel key

    98/75 Mercury Keeps shearing the flywheel key. Starts and runs then makes a noise and shears the key. 4 keys so far. Nut is torqued to 85#​
  13. jerryjerry05

    No spark Johnson

    1999 9.9hp. pull start. I've tried the tests from CDI and they said I needed a new stator. Replaced it and still no spark. The CDI instructions aren't as clear as I'd like. Anyone have the procedures from Johnson? I have a DVA test meter. Thanks,Jerry
  14. jerryjerry05

    Header bars.

    Was wondering about the header on the posts. I know your rank goes up with the amount of posts you make. What are the orange slashes under the name for? Thanks,Jerry
  15. jerryjerry05

    Lost spark 2 cyl of 6

    1998 200hp. Lost spark on top 2 cyl on the left bank. Comp good on all 6 All coils good. I have test procedure from outboard ignition . com and plan on doing them soon. Just looking for any shortcuts or quick fixes or hints. Thanks,J
  16. jerryjerry05

    TAMD 70C Parts

    The parts rotted out , Volvo wants $460 It's #19 on the induction Manifold and after cooler. Any one have a salvage yard or know where it can be gotten(other than Volvo)?? The owners a local treasure hunter that hasn't gotten rich(yet)(others just found a mil last week) need a used part if...
  17. jerryjerry05

    Online manuals

    Any links to FREE online manuals? I'm working on a 1999 40hp 2 stroke. C40TLRX Thanks,J
  18. jerryjerry05

    99/40hp.Drive shaft seal. Replacing??

    Yamaha expert!!! I need help. I have a 99 40 with a leaking driveshaft seal. The parts come as a kit and I don't wanna screw up anything when I try to replace them. Any hints or directions?? You can PM me. I sure appreciate it. Thanks,J
  19. jerryjerry05

    1996 8hp

    96 8hp 8MSHU How to remove the lower unit. The bolts came out and now I need to know what to do to release the shift rod??? THANKS!!
  20. jerryjerry05

    Shipping

    I need to ship a 225To Tn. Anyone ever mount one on a pallet? Any tricks or shortcuts?? Pictures would be great. THANKS!!!! If you can help send me a P M. Mods, please put in the right section. Thanks
Top