Search results

  1. jerryjerry05

    Force 9.9HP 1991 outboard

    Shift interlock rod not a cable :( #10 activates #1
  2. jerryjerry05

    Force 9.9HP 1991 outboard

    It could still be stuck. The cable locked?
  3. jerryjerry05

    Force 9.9HP 1991 outboard

    Sounds like the shift interlock is stuck??? Pic of the pull start?
  4. jerryjerry05

    Tachometer for 1974 135hp

    Get one and try?
  5. jerryjerry05

    Tachometer for 1974 135hp

    Won't work. You need a 20 pole tach. They went from a 20 to a 12 pole in the early 90's Google 20 pole tach and see what shows.
  6. jerryjerry05

    1978 Chrysler 85HP Powerhead Swap

    On the older stuff the gears aren't usually marked(unless your real lucky). You'll need to count the teeth Chrysler/Force used different gear ratios on all motors until about 90 or 91 Then they used the same gear sets on everything from 90hp-150hp including the L-drive.
  7. jerryjerry05

    Trim tabs.??

    19ft center console 115Yam 4stroke. QUESTION: is a 19ft too small for trim tabs and if not what size tabs?? Thanks
  8. jerryjerry05

    Odd running behavior

    Try the starting fluid test: start motor, spray starting fluid around the intake side of the motor. If the spraying makes a difference in the way it runs, then it's sucking air and needs work.
  9. jerryjerry05

    Odd running behavior

    What's the rpm's in N ? Should be 750-800 in gear in the water. About 1100-1200 on the hose. Compression? These 2 cyl. motors can run on just one cylinder, make sure it's firing on both?
  10. jerryjerry05

    1996 Force 120 with crazy compression numbers

    The factory doesn't really post the comp #s as they can vary so much. The later models were actually designed with the top/bottom cyl. comp lower than the two middle ones. The #s I remember are 155 #1/4 165 #2/3 I've seen the results as high as 175-180 on a 94 120 You sure it needs all those parts?
  11. jerryjerry05

    1980 Chrysler Sea King 15 Overheating/Waterpump Concerns

    What's the temp on the sides of the cylinders? The plug area is gonna be hotter than the rest. Doesn't look like there's a cooling passage there??
  12. jerryjerry05

    88 50 hp Force No Spark

    From what I see the muffs are the wrong ones?? The pics show the one needed. I doubt you'll find them?? Just cut down a regular muff.
  13. jerryjerry05

    Lower Engine Mount/Shock advice

    The difference is probably the paint??? Ones blue the older is white??
  14. jerryjerry05

    Alpha One Gen 2 Outdrive not going back on

    YEA!!! I used an assortment of 2x10x12 blocks and just built them up to the right height. Left the Cobra in either gear f/r, it changes gear to N when it slides all the way in.
  15. jerryjerry05

    Gimbal Bearing Compatibility and Source?

    60794A4 early# 30-879194A02 superseded Just make sure you get OEM Installing, it shouldn't be real hard to install if you have the right tools. Make sure the hole is spotless and when inserting, perfectly straight. Align the grease hole too...
  16. jerryjerry05

    Volvo Penta AQ140 water coming out of carbs.

    The 140 is 125hp 1975-79 The 130 is 110hp 1975-77 Should be an easy swap. If you drop to the 130 make sure you use the Volvo prop. They just work better.
  17. jerryjerry05

    Looking to buy a 1976 starcraft holiday 21 ft. With a 165 6 cylinder engine. Engine is locked up,and was wondering if possible to rebuild that engine?

    It's a Mercruiser drive. Did a lot of Walleye fishing out of a 21 Islander. Try to get it unstuck before you buy any parts. Sometimes a couple days soak in MMO (marvel mystery oil) will help free the pistons. Worst case, remove the head, 4x4 and a 8# hammer. Start in the second and then the 5th...
  18. jerryjerry05

    Alpha One Gen 2 Outdrive not going back on

    First your in the wrong section! Find the Mercruiser repairs a little further down the page. Second, the o-rings on the shaft, remove them and clean the grease from the groove. Then reinstall and grease only the top of the o-ring. Too much grease under the o-ring lifts the ring and makes it...
  19. jerryjerry05

    Idling

    If the tanks full and not in direct sunlight. The gas should be usable.
  20. jerryjerry05

    Water in cylinders

    Time for a new boat. Gonna refinance the house and get a NEW boat!!
Top