Search results

  1. R

    Waterproof Thread locker

    Permatex’s Thread Sealant ...I did the bolt threads on the engines no leaks or no corrosion the threads ..
  2. R

    End of Season Maintenance

    look up the gear oil and change it if is an off color .... also the water is in it and it is a milky color..inspect the air pressure 7-10 PSI..see if its a leak .... you inspect it in the fall great !
  3. R

    Mercruiser pre alpha trim pump.

    the trim pump inspects the commutator and the brushes ....the brush holder is pitted and the brushes are binding ...merc is a steel brush holder ... dc motors are a bronze/brass brush holder is very good no corrosion .. I am a electrical electronic tech ... I repair motors ... DC motor trains
  4. R

    End of Season Maintenance

    rodents and insects keep it out of my boat ,,, my woodland area ..................
  5. R

    End of Season Maintenance

    I inspected in october boat .. take out the out drive see if its water and the bellows . lube it .. then out drive is inspected the oil is clean , then flush out the water in the engine ...use a air compressor .. .then use anti freeze in the engine ...then I did marvel mystery oil 1 OZ in the...
  6. R

    Mercruiser 470 Only Showing 10 volts

    my wellcraft MCM470 conversion the AC generator ...the MCM470 regulator had a lot of failures AC generator works over 15yrs ... then I drain the sea water plug under the heat exchanger ....drain it out .. also the drain plug is a zinc and the heat exchanger is not with no corrosion .. I changed...
  7. R

    New to boats and about to burn down my boat. Need some help with wiring.

    yes the ignition sensor .... creates a lot of moisture ...
  8. R

    Alpha 1 gen 2 shift cable adjustment

    yes the brass barrel is 4 turns and then in fwd throttle gear cable then look up the shift out drive ... then the amount is around 61/8-61/4 inch ... the other video
  9. R

    Alpha 1 gen 2 shift cable adjustment

    adjust the inspect,, the shift cables
  10. R

    Oil change on Mercruiser 3.0 alpha

    Quicksilver 25W-40 Marine Engine Oil for MerCruiser 3.0 ... about 4QTS .. look up your manual on the internet ...
  11. R

    Gauge making me crazy

    the chart is ,,,,taking the wire off the water temp sensor then use a ohm meter then see if the chart is ?
  12. R

    Gauge making me crazy

    yes the wire sender is on the block ground then the sender is 260F.... gauge you did it is correct ... the temp gun is outside the engine .....drops the temp metal outside.. I know the water flow parts are changed ...
  13. R

    Gauge making me crazy

    the water engine temp is 210F the temp sender in the engine .. then the temp gun is outside the metal engine 160F ..... I would be the 140-150F temp sender on the spec temperature ..
  14. R

    5.0 mercruiser 0M361530 carb

    I know the boat ICM is the semiconductors and the engine creates a high temp around the ICM ...then the engine runs down .the semi-connectors in today world is a lot of $$$..
  15. R

    5.0 mercruiser 0M361530 carb

    the boat wiring is a smaller gauge wire from the battery to the ignition key. typically 11.5DC on the dash voltmeter panel....then the engine starts and the voltage meter is around 14 DC..
  16. R

    5.0 mercruiser 0M361530 carb

    so the engine runs great 20 min ,,, then the engine drops the power ?,, could be the engine runs correct heat then the ignition components breaks down..ICM ..
  17. R

    Mercruiser 470 Starter

    so you fix the engine starter ? you can buy the starter MHA7016 STARTER MOTOR ,,,,,MCM470 1978...
  18. R

    Runs great on muffs but not in lake

    the ignition is working good .. but the fuel is dropping when the high power engine is not lean amount of fuel .. filters ,fuel pump, gas tank vent clean ...
  19. R

    Merc 5.7 Keeps Shearing starter bolts

    the bolts are a correct length and the shoulder bolt was solid along the starter motor case . did those bolts are a high torque ,,, look up the head bolt spec ?
  20. R

    New to boats and about to burn down my boat. Need some help with wiring.

    use the ohm meter to the gear shift switch ..take the wire off and test the ohms .. short/open .
View older results
Top