Search results

  1. jerryjerry05

    Dirty hull

    Boat,22 Winner has rust stains, and brown stains from the water. I've tried Comet soft scrub,it works a little. Anything work?? Thanks,Jerry
  2. jerryjerry05

    Stains on the hull

    Working on a 22 Winner The hull has brown stains from the water, rust stains and I need to get rid of them. What works and what might work? I've tried Comet soft scrub and it works a bit. Will black streak remover work? Thanks,Jerry
  3. jerryjerry05

    87' 85 force engine gear box

    Re: 87' 85 force engine gear box The first pic is the fill/vent.Second is the pivot pin.DON"T TOUCH!!! #3 is the drain plug. The fill/vent screws, fill from the fill untill the oil comes out the vent.Then from the vent till it comes out the fill, ten again from the fill. Might be overkill but...
  4. jerryjerry05

    85 hp reed valves

    Re: 85 hp reed valves Gas spitting out the carbs too. Picture of the reeds? The pics are from a Mercury225 But they show a set of reeds that are closed the right way. Te one pic shows a reed too far open. I've go some spare reeds in the holder if interested?? Send me a PM.
  5. jerryjerry05

    1988 85 hp force overheat buzzer not working and engine does at idle. Please help

    Re: 1988 85 hp force overheat buzzer not working and engine does at idle. Please hel Take a piece of wire. Strip both ends. Then key on,touch the orange lead lug to the black lead lug. That grounds out the sender making the buzzer sound off. Too much stuff added to the gas, can do damage to...
  6. jerryjerry05

    Help 1990 force 90 HP flywheel removal

    Re: Help 1990 force 90 HP flywheel removal Nothing holding it on but the pressure. Sometimes the darn thing just won't cooperate. You'll need to drill,tap to the next size.Then use heat after it's installed. Your probably gonna ruin the top seal but it can't be helped. I had one that WOULD...
  7. jerryjerry05

    please help me serial number/ model number

    Re: please help me serial number/ model number After the manual came out, they changed it to 1 turn out and leave it there. Too rich and it can carbon up. The impeller in most cases is all you need to change. Again depending on Model? There are 2 impellers to choose from. Post a pic of the pump...
  8. jerryjerry05

    Parts, older Chrysler,before 73

    Anyone know of a parts site that has older Chrysler parts? Need the diagrams for Chrysler 1975 and older. Thanks,Jerry
  9. jerryjerry05

    '84 Force 85 hp only firing on 2cyl

    Re: '84 Force 85 hp only firing on 2cyl You sure the middle carb is feeding? Sometimes ??? The seat will swell and not let fuel in? (gas at the front of the intake)The reeds behind the carbs,nothing missing,nothing cracked,not too far open? The first pic shows the reds closed normal.The...
  10. jerryjerry05

    please help me serial number/ model number

    Re: please help me serial number/ model number Yes,change it. It might work but as it's set for a long time. The vanes have probably set with a curve in each one. Look on the starter. Sometimes it's still original. Or under the rear cowl there is a foundry stamp with the year. Or under the...
  11. jerryjerry05

    '88 Force 85hp low top speed?

    Re: '88 Force 85hp low top speed? First ask yourself?? Can I change the plugs on my outboard? If you can, then you can do it? You'll need a compression tester, then spark plug testers. Then you'll need a couple things. A remote starter and a way to ground the plugs. The red wires are the way...
  12. jerryjerry05

    89 Force 85 Lower unit...confusing

    Re: 89 Force 85 Lower unit...confusing I THINK!!! That's the seal that goes in another part. The rubber bellows went by/by and it was replaced with a new/old style cover. You only have the seal and need the plate. Look up the part #s #53 in the diagram. Someone listed a replacement part on...
  13. jerryjerry05

    1987 Force 125hp

    Re: 1987 Force 125hp Just remember the slotted screw on the middle of the lower is a do NOT touch. The drain should be an allenhead set screw.
  14. jerryjerry05

    86 force 85 hp

    Re: 86 force 85 hp That line you see is the recirc system. #2 runs the pump.It gets vacum from a hole behind the pump. Check the diaphram. The bottom piston cover has the linkage hooked up on it. The 86/85 carb could have a screw/spring on the top front. Or just a screw. It shouldn't have a...
  15. jerryjerry05

    Question On Setting Timing 1993 90HP Sportjet

    Re: Question On Setting Timing 1993 90HP Sportjet Use a jumper or jump box to get past the neutral safety switch. The throttle needs to go all the way forward. Cranking speed is, plugs out, throttle open all the way(might need someone to hold it) key switch on. Then as the motor turns that's...
  16. jerryjerry05

    Yamaha Alarm System

    What signals should I get? Is it like the Mercury's. Intermitent tone=oil? Steady tone + overheat? My neighbors 2008 200 when the oil gets low it sounds a steady alarm. The pump under the deck for the oil works but when the tank on the motor gets low it won't automtically fill??The sender in...
  17. jerryjerry05

    Force 120 Stumbles - Runs Fine Wide Open

    Re: Force 120 Stumbles - Runs Fine Wide Open You said you " I thinned out the oil mixture a bit thinking that maybe the engine had picked up excess oil sludge in the bottom of the tank, and maybe I had added too much oil the last time i used it" This could have scored a cylinder or 2. Do a...
  18. jerryjerry05

    Chrysler impeller / water pump (70's) missing top plate & driveshaft stacking order

    Re: Chrysler impeller / water pump (70's) missing top plate & driveshaft stacking ord Re: Chrysler impeller / water pump (70's) missing top plate & driveshaft stacking ord Depending on the lower unit?? You might need a special muff?? The motor should be able to draw enough water to prime if...
  19. jerryjerry05

    Parts

    Hi all. I need the transom mounts for a 88/89 85/90/120/125 With the through transom bolts. I had a pair all ready to mount on my motor and I think someone collected them for aluminum scrap. EDIT I have a setup of 50hp trim/tilt. I'll try to post a pic.
  20. jerryjerry05

    Force 50 hp Lower Unit Leaking Oil & Water from Bolts

    Re: Force 50 hp Lower Unit Leaking Oil & Water from Bolts No the seal can be pulled from the outside. The oil can be filled at anytime,cold/hot. The unit will heat up and expand the oil and when it cools it will suck in water. If your gonna buy a kit cahnge all the seals. The iboats site...
Top