Search results

  1. jerryjerry05

    Problem starting engine

    Re: Problem starting engine Timing usually doesn't move unless someone is tinkering. Very easy to rebuild/clean the starter. I think they sell brushes here. The jig for holding the brushes,I made is from an old license plate.
  2. jerryjerry05

    Boom!

    Was out boating and one motor stopped. No spark. My meter and timing light is in the shop being repaired. Both Electro Specialist products.That's besides the point. I have a second(and a third)stator in my parts in so I thought I'd just change the stator. Thought this would be a good time to get...
  3. jerryjerry05

    85 hp flywheel wont come off

    Re: 85 hp flywheel wont come off I "ONLY" use a 3 jaw puller. Make sure that you loosen the nut and reinstall it loosely. Tighten it with an impact till you think it's tight then a bit more. Then hit screw with a good size hammer. Keep hands and fingers away. Of course safety glasses. My boss...
  4. jerryjerry05

    No high end on Force 40 hp

    Re: No high end on Force 40 hp Post some pics of the float. MOST kits are crap.It's best to reuse the old stuff. Check the fuel pump diaphram.Check the jets for blockage. TINY,TINY holes could be blocked??? The pics show the right float(black) and the float level. The drop should be just about...
  5. jerryjerry05

    Force Flywheel replacement question . 1987, ELPT, SN# OE250062 75 HP Cross reference

    Re: Force Flywheel replacement question . 1987, ELPT, SN# OE250062 75 HP Cross refer Post a pic of the top and underside of the wheel. And the timing marks too. They made a few different wheels. The 97 used Mrcury parts. So the earler Force parts won't work. Post the pics. The photos show 2...
  6. jerryjerry05

    1992 force 40hp cooling

    Re: 1992 force 40hp cooling If the old impeller came out in pieces??? Then some pieces are probably still in the tube. Try to clean them out. The 40-50 needs a special muff.The big one doesn't seal right. If the tube isin't clogged try taping the muffs and tape it good.
  7. jerryjerry05

    Mercury EXPERTS???2001 125 4cyl

    125 Ser OP325500 @ up. 4 carbs. The top 2 have air screws with springs.Out 1 and 1/2 The bottom 2 have the screws no springs.I think they are screwed in all the way???? Should it have them? It starts and runs.Idles crappy. Good compression,good spark.Plugs burning right. Once it gets going it...
  8. jerryjerry05

    Chrysler mid 80's Quadrajet 4bl.FIXED!!!!

    New plugs. Hard starting. Once it's running it's great. Turn off and it doesn't want to re-start. Just went through the carb. New accelerator pump.Good gas. When the breather is off: Motor warm. The choke plate is closed. Sometimes it will start right back up. Sometimes not. Sometimes it needs...
  9. jerryjerry05

    1986 bayliner force tilt fluid change

    Re: 1986 bayliner force tilt fluid change Like food said,figure out what 's in there. Pink/red is T/T fluid. The other is probably 30wt. I use the oil can to fill,works great. Then while it's DOWN remove the cap and fill. Then cycle it a couple of times,then fill again. Do this till it stops...
  10. jerryjerry05

    READ!!!!!!!!!!!!!!!!!!!!! ETHANOL DANGER and the stores we frequent!!

    Sent this to Auto Zone!!! ETHANOL resistant hoses and additives??? I've replaced hoses on dozens of boats and now I'm wondering how safe they are??? SO ASK if it's resistant?? I recently was in your store.Bought 10ft of 5/16 gas line. Actually bought 20 ft./2 trips. I bought this to replace...
  11. jerryjerry05

    Compression tester

    Re: Compression tester Ones a push in(crap) the other's a screw in:) The valve in the hose??? It's supposed to be there.This a push in tester? Or a screw in? It works on the principal that the pressure in, is way more than the valve can stop. then it goes into the guage and is released when...
  12. jerryjerry05

    1989?? Evenrude,won't run unless it's at high speed.

    About a 1990 9.9 Evinrude. Starts and runs only if the choke is used. Push it back in it stalls. Will start right back up but won't stay running. Will run as long as you choke it. New impeller. New fuel pump. Cleaned carb(maybe should do it again). New gas/oil. What's the initial setting for air...
  13. jerryjerry05

    125hp lower gear case completely dry, no signs of leak, why ??

    Re: 125hp lower gear case completely dry, no signs of leak, why ?? These can be bought here(I think). Or at Wally's For the novice. The only way to fill the lower.J
  14. jerryjerry05

    88 force 50

    Re: 88 force 50 The regular round muffs can make the 50 overheat. You need the muffs in the pics. Most of the exhaust exits through the snout on the bottom. The holes on the back are relief ports. Their there for excess water when running wide open. To test the sender.The buzzer might take a...
  15. jerryjerry05

    Question about pulling the Flywheel and tools on a 75 HP, ELPT , 97 Force Motor.

    Re: Question about pulling the Flywheel and tools on a 75 HP, ELPT , 97 Force Motor. First a no spark probably could be something different. It could spark even if the key has sheared. http://www. cdielectronics. com/ downloads/ troubleshooting Remove the spaces. Try testing the...
  16. jerryjerry05

    1989 force 50 temp sensor r&r

    Re: 1989 force 50 temp sensor r&r Profile,location? You might be close to someone who can help?? If the temp sensor is setting off the buzzer you need to figure out if it's really bad or really WORKING!!! When it's running you should be able to touch the head and not burn. Running in a...
  17. jerryjerry05

    slow turn over on 1997 force 120..starter??

    Re: slow turn over on 1997 force 120..starter?? Take the starter apart and check the brushes for wear or sticking. A dirty /corroded starter could do this. Then try removing the plugs and a compression test. Post the results. The pics were of a working very weak starter.The springs were...
  18. jerryjerry05

    125hp lower gear case completely dry, no signs of leak, why ??

    Re: 125hp lower gear case completely dry, no signs of leak, why ?? Your not draining from the drain plug.See pic The screw on the side(pic2) is a no-no.Make sure the bottom screw is removed. Profile?? Location?? You should take it to someone who can help???
  19. jerryjerry05

    1988 force 125 carb float issue

    Re: 1988 force 125 carb float issue Post pics??? The 88/87/86/85 and a lot more all fit. the circle with the # is the year it was made. Different carbs have different jets depending on local. Mountain boats have different than ocean level. I put in a pic this is how it fits.They should all be...
  20. jerryjerry05

    Evinrude VRO Disconnect

    I'm working on a Evenrude swap An 88 for an older 110??? The Vro was disconnected a long time ago.Still has the VRO pump(gonna change that over too). There are oil lines??? Small hoses (4) from the intake manufold to the powerhead. Should these be blocked or replaced? They are cracked and...
Top