Search results

  1. jerryjerry05

    Motor pops out of gear when you give it little gas

    Re: Motor pops out of gear when you give it little gas The lower unit.Inside it has a part called a clutch dog.The edges have wore down and are letting it slip out of gear under load. #27 on this diagram. Not your lower unit but part looks the same. It can be resurfaced.You need to check the...
  2. jerryjerry05

    1984 85HP Chrysler Force Fuel Filter

    Re: 1984 85HP Chrysler Force Fuel Filter This site sells parts ,try to support them and this forum. If for some reason they don't have it here. Boats .net has the parts.F658803 $1.35 Gasket F438617 Filter $3.36 The last part is the diaphram $3.00 F438747 I've never replaced one or the...
  3. jerryjerry05

    1979 15hp Evinrude

    I just picked up a locked up 1979/15 hp Rude. Any place to get the bore size and stroke? Need a good place for pistons and bearings too. Will buy Wise-co if no suggestions. A downloadable manual would help a bunch. I know Forces/Chryslers but got this for free and am thinking about a rebuild. If...
  4. jerryjerry05

    The catfish from HELL

    Was fishing with a friend and she caught a small catfish. She tried to take it off the hook. The fish started jerking and jumping and a side fin sticks her in the palm and breaks off. She acting like she's gonna DIE!!!I'm thinking she's WAY overreacting. She's whining and about an hour later...
  5. jerryjerry05

    Bendix gear

    Re: Bendix gear Usually the reason for this is: weak starter,cheap starter(some Chinese starters are real crap).Weak magnets,bad brushes(again Chinese inferior products. It's almost impossible to find good repair parts.Even Mercury uses some Chinese crap. Take it apart and check the condition...
  6. jerryjerry05

    On thin ice

    Was at Houghton Lake,Houghton Lake,Mi. Wanting to check the ice so I could fish.I walked out about 15 ft.and stopped.The ice was too thin to walk on. So I turned around and started walking back in and about then a snowmobile with 3 people went by and they slowed down for some reason and the ice...
  7. jerryjerry05

    Too close!!!

    Worked at a Bayliner dealership. They had sold a 29ft with twin I/O's They were prepping it to put in the water. They had it up in the slings to change trailers. The new owner was all around and trying to get up in the boat and putting his nose everywhere. I told him it wasn't a good idea to get...
  8. jerryjerry05

    78 OMC 190, where's the water intake?

    Re: 78 OMC 190, where's the water intake? Should be on the lower unit. 4 holes on both sides of the lower.#3 It needs a big bucket or muffs.
  9. jerryjerry05

    My Doctor friend or Dr.s aren't as smart as they think!!!

    Around 1990.I lived at a marina and had been drinking buddies with a Dr. who bought a boat from the dealer where I worked.Bayliner 1988 28ft 460/King Cobra. I was entrusted to maintain his boats. One of his Dr.friends decided he wanted to maybe buy the boat.They take off for a 3hr cruise(nothing...
  10. jerryjerry05

    Help, need to ID my bearing carrier, lower unit was replaced and unknown year or make

    Re: Help, need to ID my bearing carrier, lower unit was replaced and unknown year or That should just knock out if the screw is removed. Deep inside there might be 4 bolts holding the carrier in. This is a lower from 1990 5.7 The pics attached. http://www. boats. net...
  11. jerryjerry05

    Thermostat for 105 model 10576 SN 1161

    Re: Thermostat for 105 model 10576 SN 1161 That's not a seal.That's a guide tube.It helps align the tube from the motor. There should be a seal on the top of the pump housing. Without a seal your not gonna get the results you need. If it ran without a thermo then it aint gonna hurt till you...
  12. jerryjerry05

    Replace steering wheel?

    Re: Replace steering wheel? Not really up on the jet boats or PWC's But a quick question. Is there a steering fin on the bottom of the jet pump or nozzle? I see on the 90 Sportjet there is a zinc(very bottom) that looks like a fin#23 see pic.. Is the fin adjustable.If so then try adjusting that...
  13. jerryjerry05

    1989 Force 150 HP TILT and TRIM

    Re: 1989 Force 150 HP TILT and TRIM You need something like this to keep your motor tilted up while trailering. It's kept on with a cotter pin/or circlip. If you get one it fits a special way(I can send pics)For some reason I can't upload here anymore!!! Some can be found on e-bay. The e-bay...
  14. jerryjerry05

    Parts manuals

    Anyone have a link to parts manuals for jetskis or waverunners? Looking for the ones who use Force motors. Or the drives. Need to know if there is any kind of steering fins on any PWC or whatever??? Pictures would be great!!! THANKS,EVERYONE!!!!
  15. jerryjerry05

    Pulling Flywheel, threads maybe stripped,1978 Johnson 150 hp

    Re: Pulling Flywheel, threads maybe stripped,1978 Johnson 150 hp The threads are usually 1/4-20 I think???Usually they strip out the first time you try to get the flywheel off. Use PB Blaster on the top of the shaft. The best thing to get is a BIG 3 jaw puller.See pics.Auto Zone has...
  16. jerryjerry05

    new owner

    Re: new owner That Cobra is the worst one for parts. The manifold is not available ANYWHERE. If it goes the rest is scrap. They run real good and are pretty fair on fuel. The 2.3 is the smallest and the lower unit of the drive is way smaller than the rest. The King Cobra is the bigger units...
  17. jerryjerry05

    Pulling the flywheel

    Re: Pulling the flywheel Sometimes that puller works sometimes it doesn't. Most times it strips out the bolt holes. I always use a BIG 3 jaw puller.See pics. Loosen the nut(don't remove)install puller. Tighten with an impact or as tight as you can get.Then a little more. Hit the puller bolt...
  18. jerryjerry05

    Force 150hp tough start after sitting up

    Re: Force 150hp tough start after sitting up Do a compression test.Low comp on 1 cylinder can make it hard to turn over. Make sure the batteries are load tested.Probably not the problem. Bad starter?How old?Overheated? Starter could look like this? The starter cleaned/rebuilt.Brushes? Turning...
  19. jerryjerry05

    my chrysler 45hp wont pump water

    Re: my chrysler 45hp wont pump water How old is the impeller? You running on the hose or a bucket?Needs DEEP bucket!!!! Some muffs won't work on the smaller motors. They take a special muff. Is the copper tube going up to the head loose? Profile,location?
  20. jerryjerry05

    hydraulic steering

    Re: hydraulic steering http://www.teleflexmarine.com/products/ This is what i use on my twin Force outboards. Installed it 21yrs ago and had to replace only 1 seal(free) They might sell these on this site. My boats an 88 with twin Force 85's The steering was rated for up to 5 or 600 hp(I...
Top