Search results

  1. mickyryan

    aquasport 175 osprey

    I went with this one cause its light weight :)
  2. mickyryan

    aquasport 175 osprey

    It was short a couple pieces bit 1.5" pvc works with nylon fittings perfectly so crisis averted !
  3. mickyryan

    aquasport 175 osprey

    Now im gonna make a hard top to go on that
  4. mickyryan

    aquasport 175 osprey

  5. mickyryan

    aquasport 175 osprey

  6. mickyryan

    89 Rinker Restore: Seeking suggestions for new SBC350

    Found ya !!
  7. mickyryan

    aquasport 175 osprey

    I'm just using the resto for physical therapy, eyes seem to be issue atm not bad just reading text seems to be issue got some new glasses yesterday so hopin that helps thans for all the well wishes im still plugging away
  8. mickyryan

    1973-74 larson shark 1550

    prefer bunks here as well just feels safer on bottom of boat and boat stays put on the road with proper straps of course
  9. mickyryan

    1987 Power Play XLT-185 - floors, stringers, and upholstery

    lookin good seems you are moving rt along now !
  10. mickyryan

    1969 Mako cut and gut project by Lectro88

    i use bcx ply haven't had a issue i usually do a layer of csm between the ply or 6 oz fabric, my transom on the aqua sport is 3" as that was max thickness Yamaha recommended , i also did a extra set of stringers to my transom on floor because all the engines are heaver now adays then when my...
  11. mickyryan

    1969 Mako cut and gut project by Lectro88

    grats on the cap removal i figured it was transom holding you together the most
  12. mickyryan

    1969 Mako cut and gut project by Lectro88

    last 2 builds i had no cradle but i did make sure that the bottom was well supported and not flexed by bunks i can see a hull getting out of shape by a roller and then you glassing inside and that keeping the out of shape shape , same with bunks if not on a chine
  13. mickyryan

    Rehab SportCraft 222 1983 deep V hull cuddy walkaround

    man i feel your pain, i woke this mornin it was 61! one more degree and wed been falling out trees like the iguanas!! :)
  14. mickyryan

    Stern drive/inboard engine - sealing transom ring

    seal that wood up good that is more important then anything else, if you are worried about the screws i would use 4200 or pl marine and dab it in the holes before running screws in if not going to drill oversize and epoxy and redrill.
  15. mickyryan

    Fibreglass boat floor replacement - do I need to use fiberglass?

    if you cut two holes with holesaw in each cavity it will allow excess foam to come out then you plug those holes and put your last layer of csm or 1708 across floor and done. you need to use at least 2lb closed cell foam or it will absorb water, in other words great stuff not gonna do it for you...
  16. mickyryan

    ‘73 Bee Craft

    well couple things , looks like you gonna need a new tank since you seemed to cut across it , if i am wrong ignore me , other thing , i would remove cap and while you do the stringers cut out bedding in cap and replace that too if needed, good luck imma ride along if ya dont mind , looks like a...
  17. mickyryan

    Rehab SportCraft 222 1983 deep V hull cuddy walkaround

    is ya cold KC? btw if you get on facebook i go by Micky Ryan there so easy to find:)
  18. mickyryan

    Opinions? - Spraying Gelcoat Difficulty??

    I personally used a husky hlvp that i drilled out with a bit so the tip would flow better if i can find the bit and check it i will let you know but it works flawlessly for my use and its basically throw away if things go bad i put the bit up with tape on it to tell me it was the bit but now i...
  19. mickyryan

    I found an awesome DIY repair YouTube channel

    glad you found them yeah they do great work and have many good videos. another one thats been around awhile is Frisco boater he did a sea ray restore and documented it well https://www.youtube.com/channel/UCqz13HCBRHihm2L883-7UlA
  20. mickyryan

    Transom seal over existing?

    clean bilge with good degreaser loom up wires and clean up install but painting is just a coverup if there is no problems go for it if you see a problem fix it :)
Top