Search results

  1. C

    Has anyone used the ready lime (not the brand name) to descale their outboard

    It is more useful to add a bit of garlic and onion powder and some oil to the vinegar and salt mix and pour it on your salad.
  2. C

    1972 80 Hp Mercury enhine

    I wrapped my hydraulic lines with electrical tape. It looked OK and lasted many years.
  3. C

    Has anyone used the ready lime (not the brand name) to descale their outboard

    You realize that vinegar and salt mixed together is not HCL, right? There are 10K perpetual motion machines on the internet as well. Those are crap as well.
  4. C

    Has anyone used the ready lime (not the brand name) to descale their outboard

    Gee, I am not sure how to fill and seal the cooling system of an outboard. I doubt vinegar will do anything. What is the purpose of the salt?
  5. C

    I want to place a metal patch on a Zinc-Coated steel gasoline tank opening.

    Top of tank right? Standard fuel tank gauge senders are sealed with rubber gaskets and self tapping screws. Tanks are vented, so no pressure build up is expected.
  6. C

    Has anyone used the ready lime (not the brand name) to descale their outboard

    I pumped this stuff thru my motor for 4 hours. I am not sure it made a difference. Any other opinions?
  7. C

    ETEC Emm Issue

    I saw a video of a guy working on a FICHT, which is the father of your motor. It has 4 fuses in a plug, attached to a cable. The fuses were under a cover, that looked like a cable terminator. You might look for such a thing, if you did not find 4 fuses together.
  8. C

    ETEC Emm Issue

    Does that e-Tec have any fuses?
  9. C

    1963 Starcraft Jupiter 16ft Windshield Brackets

    My '62 Crestliner had small U shaped brackets to hold the very bottom back edge of the windshield to the deck. Is that what you are looking for?
  10. C

    Shift rod position after impeller change

    The mechanic may be correct. The shift cable could have been set (by the mechanic) just a bit wrong. Set the control to neutral. Disconnect the shift cable at the motor. Now move the shift lever until centered in the neutral position. Adjust the shift cable to match the shift lever and...
  11. C

    Jet Drive Outboard Motor Debris

    Gee, don't jet drives pull most of the water straight up from the bottom? I would not expect the keel to affect that. I would expect the keel to affect a prop drive, as the prop pulls water from under the hull.
  12. C

    1987 Mercury 150 xr2 Blackmax Newbie Help

    Gee, the impeller may be good, the carbs may be clean and the timing may be right. However, the motor setting for any length of time often causes or worsens the condition of the carbs and impeller. Any of those not working or not set correctly can ruin the motor.
  13. C

    Converting jet to prop

    You might check the Sterndrive Engineering (SEI) website. Your motor is new enough, I would think, to buy a new gearcase from them.
  14. C

    1987 Mercury 150 xr2 Blackmax Newbie Help

    Gee, if it were me, I would change the gear oil, replace the impeller, wearplate and two gaskets, clean the carbs and check the ign timing.
  15. C

    Mercury 1982 70hp Bluestripe Foot/Gear case

    Crowleymarine will have the parts list for your motor. You should be able to get the part number for the gearcase. Now, whether you can find a used gearcase for your motor is a different subject. Alternatively, you could try a prop with 20% more pitch.
  16. C

    Tilt trim making weird noise.

    Grease the tilt tube.
  17. C

    Am I hurting things by not running WOT?

    You want to prop your boat so it will run at max recommended RPM at WOT. That gives keeps you in the motors powerband properly. Lugging the motor is bad on several levels. Once you have that, pick a speed that you like and run it. As for best economy, solidly on plane and trimmed near max...
  18. C

    Livewell design

    Why do you have the drain connected to the fill hose? All it will do is clog it with fish guts. You could connect the drain to the overflow hose, low down in the hull. That makes sense.
  19. C

    Is a 4.3 Mercrusier Waterpump the same as a 4.3 Chevy waterpump ?

    The timing cover on my '88 4.3LX looked to be automotive grade, as was the oil pan. I say was, because it rusted thru.
  20. C

    Is a 4.3 Mercrusier Waterpump the same as a 4.3 Chevy waterpump ?

    Also, the backplate on the marine waterpump is stainless steel.
Top