Search results

  1. S

    Advice needed 1977 evinrude 35 hp

    Same pump kit.
  2. S

    Advice needed 1977 evinrude 35 hp

    Didn't have your exact model number but I believe this is it. Updated part number with gaskets.
  3. S

    Advice needed 1977 evinrude 35 hp

    I fixed one up and sold it this summer.....it was hard to run on muffs but I did it.
  4. S

    Engine Running Hot

    What brand of thermostat?
  5. S

    Starter not engaging after running

    Starter solenoid getting hot maybe....get it to the condition and then jump it like mentioned above.
  6. S

    New Johnson J35EL CND

    Had you just charged it when you were Spinning the motor? Have you done the other tests. Could be corroded wires, bad soloniod or bad starter. You need it to spin up correctly to get a good compression reading. If your compression numbers stay where there at you might think about get rid of it...
  7. S

    What is the function of the orifice plug

    All kinds of things but let's back up. When you run it full it's on a boat right? And not in a bucket. Turning off or starving it of fuel leans it out so yes they may lead you to believe it's running rich but it's also starving the motor of lubrication and could be doing harm to it. You should...
  8. S

    New Johnson J35EL CND

    14.5 volts on a sitting battery? Meter isn't correct.
  9. S

    New Johnson J35EL CND

    What's your battery voltage at the battery.....then voltage at the battery side of your soloniod? Then while cranking the battery, what is your voltage at the starter side of your soloniod?
  10. S

    New Johnson J35EL CND

    Do you have a voltage meter?
  11. S

    Gear shifting issue evinrude 70

    Marine shop rate in Seattle is $180 an hour. $100 is a bargain.
  12. S

    93 evinrude 25 hp primer

    Seals are probably leaking a hair. Ignore, clean or rebuild the primer.
  13. S

    Recoil pawl evinrude 25 hp

    I had a problem with my last one and it had to do with the nut tension or something. When you had it off did you look to see if the pawls were coming out instantly? Sorry I forgot what I did but it fixed that.
  14. S

    1988 35hp - Multiple issues

    I to vote that your wasting your time. When they get that stuck even if you get them out they ruin the crankcase splines. I've tried about ten and only saved one. Good luck.
  15. S

    Timing Retard

    I couldn't quite follow your problem but when most people report back firing it's because they have the wrong wires going to the spark plugs. Recheck your wiring.
  16. S

    1954 10HP Johnson crank question

    This is weird and I think it may be incorrect but your part number comes up as "impeller spacer"
  17. S

    1954 10HP Johnson crank question

    Maybe the ebay part number was incorrect.
  18. S

    What percentage of value of motor do you replace? How much to spend on parts motor?

    When your working on it while off, doing say throttle linkage adjustments, always take the throttle back down before shifting it back to nutruel. Shouldn't jam up anymore.
  19. S

    What percentage of value of motor do you replace? How much to spend on parts motor?

    I have a theory as to why your breaking your part....just not sure it applies to this motor. When your working on it when it's off, to get it to go to full throttle you have to be in forward. Now if you don't return it to idle and you shift it back into nutruel it can bind up the linkage. Has...
  20. S

    What percentage of value of motor do you replace? How much to spend on parts motor?

    Since the pandemic started it appears that parts have gone up so your motor or other motors might be worth more than has been stated. I have seen parts on ebay climb recently. Pretty sure this trend will continue with the current thinking with what's good for the planet.
Top