Search results

  1. Kola16

    2011 Tahoe Mer 4.3 - engine miss firing

    Clogged fuel filters, clogged fuel pickup tube or screen in the tank, clogged gas tank vent, faulty fuel injectors (won't show up with fuel pressure test), fuel pump going bad. Just measure the fuel pressure. The gauge can be rented for free basically at O'Reilly or the like.
  2. Kola16

    Bravo Coupler and Flywheel Question

    Darn. I even had the machine shop balance the flywheel after the rotating assembly too. Oh well more money into the pit. Yes it does have all three bolt holes for the different starters.
  3. Kola16

    Bravo Coupler and Flywheel Question

    Hello all! Long story short, is there a Bravo coupler that goes on a 153 tooth (12.8") flywheel? I am swapping my stock 350 SBC with a mild 383 SBC that will put out roughly 400+hp. Right now I have an MC-1 drive that I will run for a year or two max until I get a bravo drive. I will go easy...
  4. Kola16

    Yahana 200hp txrr stumbles at idle

    If you have the money, the CCMS composite reeds are well worth it. They improve starting/idling and hole shot. If money is tight, I am not really sure whether you should replace a set or all, but according to the Yamaha tech you talked to, you would want to replace all of them if they commonly...
  5. Kola16

    2002 225 Optimax - Overheating at idle only

    In that case, I would say it is a stuck/bad poppet valve.
  6. Kola16

    2002 225 Optimax - Overheating at idle only

    Is this engine ran through saltwater, sand, or mud?
  7. Kola16

    115 Yamaha overheat alarm at 1,800 - 2,000 RPM's

    The idle RPM tangent got me side-tracked too haha. If your engine is used in saltwater you need to clean out all the deposits from that, kind of like you did when you took the heads off. To do this you need some Rydlyme marine and a bilge pump or livewell pump to pump the Rydlyme through your...
  8. Kola16

    High compression in 1 cylinder - 7.4 carb

    Like Scottin said, the cam is actually way different. Marine cams are built with all low end torque in mind, similar to what a truck is. A cam from NAPA would leave you with a gutless boat engine. You need a marine cam and they are more $$$. Additionally, depending on where your engine is...
  9. Kola16

    Alpha One 3.0 Starter questions

    Is post number 2 viewable to anyone else? Lots of people buy amazon starters. They buy them every year because the starter they buy off amazon quits working after a year. Smart strategy by amazon selling you a new cheaply made product every year. I don't consider a starter on an inboard "small...
  10. Kola16

    High compression in 1 cylinder - 7.4 carb

    That wouldn't cause it to tick like it is though would it? If that cylinder is not firing properly, stuff is going to build up in that cylinder wouldn't it? Check the pushrods first before pulling the heads off. Roll the engine over with the valve cover off to make sure your intake and exhaust...
  11. Kola16

    High compression in 1 cylinder - 7.4 carb

    Like others have stated, it sounds like you have a flat lobe/lifter on the camshaft. Pull the valve cover and inspect the exhaust and intake pushrods for cylinder 8 to see if there is any play in them. Is it a flat tappet cam? Flat tappet cams require oil with high zinc/ZDDP. I found that out...
  12. Kola16

    Alpha One 3.0 Starter questions

    50-8M0090697
  13. Kola16

    Blogs plug housing loose and turns

    You can quickly check how much of your transom is rotten like alldodge said to do very easily. Take a hammer and just start tapping around the transom from the inside of the boat and outside. Tap on the stringers too. If they are rotten, it will make a dull, soft, quieter, thud sound. Harder...
  14. Kola16

    Need help with Hull crack in Aluminum Lowe Boat

    To echo what they said and to add on, if you want to save some money, remove the bow eye for the weld shop and brush the crap out of the area that needs to be welded with a wire brush (SS wire preferred) to remove the paint and corrosion and other nasties. That will save the shop prep time which...
  15. Kola16

    Livewell Pump Noisy

    It could be normal, it could be about to die. It is impossible to tell without a video or audio recording. I say if it works, leave it in. I have a spare livewell pump always with me cause they go out all the time.
  16. Kola16

    Overheating at idle

    What is telling you that it is overheating? A gauge? An alarm? Have you confirmed the temperature with an IR thermometer?
  17. Kola16

    Yahana 200hp txrr stumbles at idle

    This. Draining the fuel in the bowls and spraying carb cleaner in them is almost useless. The carbs need full disassembly and every square inch of the inside cleaned.
  18. Kola16

    Overheat alarm at idle... I think??

    Additionally
  19. Kola16

    Overheat alarm at idle... I think??

    Are both your oil resevoirs filled? Are the oil float sensors floating in the oil?
  20. Kola16

    Yahana 200hp txrr stumbles at idle

    What are your compression numbers?
Top