Search results

  1. alldodge

    5.7 EFI stalls when warm and shifting into gear

    Don't think smoke will work Zero counts on IAC leans me to a vacuum leak. Don't know of a port to check on the motor If MAP is off, this will mess up the IAC and fuel metering
  2. alldodge

    Volvo Penta 4.3gl Starts when in start position and dies in on positon

    Welcome There were several GL's models A thru E which I have but could be more With loosing spark when key is released from start, see if 12V is at the coil, assume it will not be there. Then check for 12V at the key on the purple wire. If no power then it's the key switch
  3. alldodge

    Reverse Polarity and no battery charge related?

    It could be one of the diodes in the boats polarity tester is burned out
  4. alldodge

    Reverse Polarity and no battery charge related?

    Reverse polarity means wiring is crossed between shore power connection and the boat. Check the shore power connection
  5. alldodge

    Electrical issue.

    The Alt doesn't start charging until the RPM is increased the first time above 1000, but once it starts it should continue to charge at idle and above
  6. alldodge

    Electrical issue.

    Number comes up as a 135, 150 and 150 seapro, you have 150 All have a alternator which is 55 amp How does the Bat check ok? Bat should measure 12.6 to 12.7V being off the charger after a few hours When motor is running you should measure 14.3 to 14.5V
  7. alldodge

    Electrical issue.

    The 1150F23ED is the model number, need serial number Most new larger 4 stroke use a alternator but does depend on size
  8. alldodge

    Windmill boat bettery charging

    I like it and thinks it will be great. Hope it doesn't turn into something that is real complicated Look forward to seeing the results
  9. alldodge

    Engine Flushing - When Boat is in the water

    I wouldn't do it because the wash down pump can not supply enough water. You would most likely wind up damaging the impeller
  10. alldodge

    1966 MFG Rebuild

    The entire iBoats server won't let anyone upload. We're working on it
  11. alldodge

    Questions about idle speed on 4.3GXI-E on startup

    Scanner Pro is good software (I have it also), but for the most part it just tells you want's going on right now, it doesn't read codes
  12. alldodge

    Windmill boat bettery charging

    Is it legal to tow a windmill, don't know, but guessing it's if it posed a hazard or distraction to others They make different types of windmills so it might work
  13. alldodge

    Alpha 1 Lower unit. Can’t turn shaft while reinstalling

    Just installed a brand new SEI alpha drive yesterday. It came down about an inch above so I rotated the upper drive shaft by hand and then it dropped to a hard stop about a 1/2 above flush. Removed and retried a few times then realized it was at the height of the alignment pins. Being a new...
  14. alldodge

    SEI preload and a stern jack

    Well the drive and stern jack is all back on. Still plan to fire it up but ran out of time again. Took more pics and will post if/when we can
  15. alldodge

    SEI preload and a stern jack

    Yes it is a Alpha and Manual 6 shows timing marks on page 3A-30 The 2 halves are back together and it's beer 30 right now
  16. alldodge

    SEI preload and a stern jack

    The Good and the Bad Good Pressed it apart, put back together adjusted rolling torque to 8.5 in lb (6 to 10 spec) Book shows torque nut 70-80 Ft lb Bad Torque may have been correct all along. Wrench is for 0-75 in lb. I was reading gauge and see 1.8 not 18 It took my strong arm to torque down...
  17. alldodge

    SEI preload and a stern jack

    When we first removed the gear/bearing assembly off shaft I tried to see if they were loose and they wouldn't budge Yea for us, oh poo
  18. alldodge

    SEI preload and a stern jack

    Thanks, watched the vid and he barely passes by it. This would mean to be I need to separate the bearings. So will do it this morning
  19. alldodge

    SEI preload and a stern jack

    Hey @Bt Doctur you sure about the 85 Ft Lb, I'm not able to find it in a bulletin anywhere Emailed you pic also
  20. alldodge

    SEI preload and a stern jack

    No I didn't press the bearing off, the bearing a gear came off easy after nut and washer was removed. I did use the hose clamp and lubed the bearings but it just never eased up. Still not able to attach pic so I sent you the pic on email
Top