Search results

  1. jerryjerry05

    70hp Force outboard idles high and Bogs down with throttle

    Testing the Enricher/ Choke: Pump the ball, should get hard, then someone at the key, you at the enricher. Start the motor, pull the hose from the enricher to the carb. If it's pumping fuel or fuel coming out? Then it might be bad?? Running, pinch off the hose to the carb, should make no...
  2. jerryjerry05

    Low Compression on Cylinder #2

    The motor you have was one of the worst Mercury/Force put out. The single carb feeding 3 pistons was a problem from the beginning. I'd try to sell the parts, you'll get more for the pieces than selling outright. Fixing? around 1200$ just a wait and see when/if it breaks again.
  3. jerryjerry05

    Force 1989 125 question

    You have this in 2 different posts?
  4. jerryjerry05

    1995 120hp Force CDI wiring diagram help!!!!

    Trigger 1989 If the tags are off?? then trial and error. Are all the wires different colors for the trigger? I've got 3-4 triggers with no numbers or codes.
  5. jerryjerry05

    New issue on the 105 water pump. Gearcase issue.

    Try adjusting the clunk in R Or it's gonna screw the Foward up too.
  6. jerryjerry05

    New issue on the 105 water pump. Gearcase issue.

    The prop: lock the motor in gear and try to move the prop? It shouldn't be able to move, but the prop turning in water will be the test. Mark the hub and go for a ride, then check the marks and see if the hubs spun. ANY!! prop repair shop should be able to rehub your prop. If not you can do it...
  7. jerryjerry05

    Chrysler 65hp clutch dog problem

    "as far as I can tell there's no adjusting forward gear in relation to the pinion gear" That's measured and set by shims under the bearing cup for the pinion gear. Get the factory service manual, you don't need the exact year, just something close. You WILL need special tools to shim the pinion...
  8. jerryjerry05

    Replace old throttle control box with newer version

    Never heard of a Force to Mercury adaptor??? Might be one but I've not seen it?? Is it too late to send it back(the new one) ? Buy one from ebay? https://www.ebay.com/itm/124882751894? 120$ hash=item1d13979196:g:mQMAAOSwPJphMXDl There should be a buss bar on the motor that the wires get...
  9. jerryjerry05

    105 water pump

    They sell parts here. If you can't find them here,?? Franz Marine should have the parts you need.
  10. jerryjerry05

    New issue on the 105 water pump. Gearcase issue.

    You don't have a thrust hub on that unit. I believe the props located with a pin. The pin keeps the prop spaced out so it won't rub. Look on the prop shaft for a hole and align with the hole on the collar of the prop. The latest parts diagram(74)doesn't show the pin??? Picture #2 shows the prop...
  11. jerryjerry05

    Chrysler 65hp clutch dog problem

    The Chrysler lower units were actually one of the best out at the time. There really isn't too much different than the new stuff out there now. The newer, bigger ones (from 88 to 95) can be rebuilt without shim tools.
  12. jerryjerry05

    1997 force 125 thumping

    The 87 will need special tools to rebuild. :(
  13. jerryjerry05

    1997 force 125 thumping

    Is it a 125?? they didn't make a 125 in 97??? Some gear cases can be rebuilt without shim tools. Just gotta figure out the model, year etc.
  14. jerryjerry05

    low compression 3.0 cobra (new)

    This a new tester?
  15. jerryjerry05

    Sport Jet 120

    Have you done a compression test? You pull the head and check the gasket?
  16. jerryjerry05

    85hp force will not start. Fuel not getting to cylinders.

    The fitting on the bottom of the reed plate is for a hose from the plenum or carb cover .
  17. jerryjerry05

    89 125 won't go into forward gear

    From the pics: both dog and gear are ok. Nordin mention the shift rod, not sure of the turns needed in or out for the right setting. Under the bottom carb is the top of the upper shift shaft, you might have to adjust it there?? Once in a while I've ran across the shaft needed adjusting. Just in...
  18. jerryjerry05

    70hp Force outboard idles high and Bogs down with throttle

    Check the fuel pump diaphragm.
  19. jerryjerry05

    Rectifier-regulator 4 wire, can I use a 5 or 6 wire???

    Why not get the right one??
  20. jerryjerry05

    1990 Force L-Drive 90hp -- Can't get it to idle -- losing my mind :D

    Thought I mentioned bad connections on the trigger leads??? 1988/85hp: started off with an intermittent miss, once the motor got hot the miss went away. Then the miss became more pronounced and would miss every now and again under power. Then it became a constant miss. One lead from the...
Top