Search results

  1. jerryjerry05

    1995 Force 120 missing

    Dave K Sent you a PM.
  2. jerryjerry05

    Carbs leaking fuel 1988 force 125hp

    They don't make them anymore, and the plastic is JUNK> Try Franz Marine or marine salvage yards. Ebay has carb sets but very expensive :(
  3. jerryjerry05

    '95 120hp compression test results

    First!!! those numbers across the board are low. With a good gauge they should be 145-155 maybe even higher, even a new gauge(Harbor Freight Tools) can give bad results. I think they started in 95 the 120 came from the factory with the top and bottom cyl. lower by 10# than the 2 middle cyl...
  4. jerryjerry05

    Lower shift rod came out of gear shift arm...re-assemble?

    No new seals needed. Just use sealer when needed?
  5. jerryjerry05

    Sputtering when at full throttle

    I can't get it to open??
  6. jerryjerry05

    Lower shift rod came out of gear shift arm...re-assemble?

    Yup, disassemble the lower and screw it back in. Find a parts diagram and use that for a reference, take pics as you proceed. You might find using assembly grease will help hold the pieces together while you assemble.
  7. jerryjerry05

    1992 Gamefisher Issues. Need help.

    The diaphragm in the pic is bad, it should be smooth and no swelling. Finding a new carb, nope. There's a used one on ebay https://www.ebay.com/itm/Vintage-Tillotson-Quicksilver-1300-F712061-Marine-Carburetor-In-Box-A2153/203343014419?hash=item2f58302a13:g:JW4AAOSwe95gY0zO But you probably...
  8. jerryjerry05

    Sputtering when at full throttle

    Helps to know what were working on? The carb can have 2 different needle/seat combo's. One needle can have a rubber tip and a solid seat, the other a solid tip and an o-ring in the seat. Some cleaners can hurt the rubber in the needle/seats and melt plastic if there's any used and can swell the...
  9. jerryjerry05

    70hp Force

    You can have one of three different styles.. A picture would really help.
  10. jerryjerry05

    2000 Mercury (Tracker) 125 2+2 motor making gas slicks in idle

    There's supposed to be a recirculation system on all outboards made after the 70's Some might not work as good as they should. There are tiny hoses that can get clogged and the unburned fuel finds it's way out. Start it and look at the front of the carb and see if any fuel is coming out the...
  11. jerryjerry05

    Engine shutting off and bulb without pressure.

    The squeezie: it has one job, it pulls fuel from the tank and feeds it to the pump and carbs. Once that's done it's job is done and once the motor starts the pressure goes away, Normal!! The valve in the squeezie is a one way valve, once pumped up it should let the pump draw through the valve.
  12. jerryjerry05

    1989 Force 35hp fuel pump issue

    If possible post a pic with your request. This fuel pump should fit motors from 1980 to 1992 The smaller motors have a different pump style, so post a pic if possible and have a ruler next to the pump. I might have an old one??
  13. jerryjerry05

    Force 70HP 1991 2 stroke Wiring Diagram

    They standardized the color code sometime in the late 70's or early 80's I found this by looking on Google and using the term "color code for marine wiring" This should get you close.
  14. jerryjerry05

    VP 280 Pins and Helmet

    FYI there are two holes in the knuckle that have 1/4- 20 threads in them. Get 2 bolts (1/4-20x 2-3" Turn them in evenly and the knuckle lifts out as you turn them in.
  15. jerryjerry05

    Is there any hope???

    The newer GM blocks will be harder to adapt your older parts. Before you spend?? do a real thorough inspection, heads, risers, manifolds etc. Looks like you have the small camera for looking into the tiny spaces. The Cobra was outdated the day they introduced it. :( The good thing is there are a...
  16. jerryjerry05

    Tach output from the motor

    Turns out it's not charging and that's probably the problem. Thanks for the reply's!!
  17. jerryjerry05

    New to me Force 120 ('92 I believe) and of course I have trim/tilt issues.

    Only $280 ?? Other sellers think they want to retire from their ebay sales :(
  18. jerryjerry05

    Tools required for lower unit reseal

    The only grease used inside the lower unit would be "Assembly Grease" It's used to hold the parts together until it's all back together. That grease melts and dissolves in the oil.
  19. jerryjerry05

    Fuel pump 1988 force 125hp

    Nordin, looks like the diaphragm has a shiny spot and maybe good? Jose. If there's no hole in the diaphragm??? it's good. Spitting from the carb: First do a compression test, then do as Nordin suggested, remove the carbs and inspect the reeds. Does it backfire? Where are the air screws on the...
  20. jerryjerry05

    Tach output from the motor

    Thanks but something I can understand? I have a DVA meter.
Top