Search results

  1. jimmbo

    Mercury 115 2 stroke won’t idle and runs rough.

    about 9 1/2mm, just under 1 centimeter
  2. jimmbo

    Can not stop wanting a Butterball Turkey.

    The USDA considers 165 the Minimum for Ground Beef, less than that is Unsafe. Myself, I go for minimum of 185, often higher.
  3. jimmbo

    Can not stop wanting a Butterball Turkey.

    With luck, all that salt in the Brine will reduce the number of Bacteria. Happy Cooking!
  4. jimmbo

    Can not stop wanting a Butterball Turkey.

    Cooking it to a Lower Temp, Longer, creates the Best Environment for Bacteria to Multiply like Gangbusters
  5. jimmbo

    Can not stop wanting a Butterball Turkey.

    190 or higher, or I will not eat Poultry I have returned dozens of Roasted Chickens to Costco, as I have seen Pinkish Meat and or Red/Pink Spots in the Breast Meat 185 is the lowest I will go with Pork or Beef
  6. jimmbo

    Can not stop wanting a Butterball Turkey.

    As long as it is cooked to at least 190F, and served the moment it comes out of the oven, I will eat it, if not, I pass. I had a visit with Sam and Ella, a few years ago, and don't want a reunion
  7. jimmbo

    Can not stop wanting a Butterball Turkey.

    Butterball...
  8. jimmbo

    Carb Needle condition / function

    Think of this kind of 2bbl as 2 Carbs, that share a Fuel Bowl, Throttle and Choke Shafts.
  9. jimmbo

    Carb Needle condition / function

    Both are Damaged, and should be replaces
  10. jimmbo

    Evinrude 85HP 1979 (85995R)

    https://www.marineengine.com/cart/index.php?prod_rn=92176&quantity=1
  11. jimmbo

    Got a new toy to test out eventually...

    I will assume it is a SD Card. SanDisk, part of Western Digital, does, or did, have a Data Recovery Service.
  12. jimmbo

    Got a new toy to test out eventually...

    What kind of Card, and what brand? Bouncing Waves while recovering from Spinal Surgery?
  13. jimmbo

    Trailer fit?

    The Boat is a couple of Inches too far back, as those Bunks are unsupported Wood. I would than either cut the Bunks, or move them forward, until the End is directly above the Connection to the Trailer Frame. that is where I would have the Transom, located. If you want to have the Transom further...
  14. jimmbo

    Got a new toy to test out eventually...

    Which Prop?
  15. jimmbo

    i have 2 mercury 90hp towers 1 is 78 one is 84

    It will fit. The 78 likely is a Older Style, with a less streamlined shape. My 78 90 had the post 78 gearcase on it.
  16. jimmbo

    Prop for Merc

    Boat weighs about 310 lbs. Looks like what used to be called a car topper Is just shy of 14ft Is rated 40hp Max. 45kmh is about 28mph, which appear a bit slow for a 14ft with a 50, we used to get better than 30 with a crank rated 35hp on a 14 ft Rpms are low, but maybe the Tach is not set...
  17. jimmbo

    Mercruiser 4.3 Prop Question

    If you want higher top end, ditch the 4 blade, and reprop with a 3 blade to attain the 4800rpm What condition is the Engine in Mechanically, as in what are the Compression Test Numbers?
  18. jimmbo

    What accurate humidity level in full basement stops all mold ?

    I keep mine at 30-35% yr round, and I would go lower if I could
  19. jimmbo

    Suggestions on how to fill my onboard gas tank?

    I will stand with that Statement. I had read about it several times back in the 70s
  20. jimmbo

    I Know What Happened But Why?

    If the Flywheel Nut has been over torqued, it stretches the Taper, and that can cause Problems, including Shearing, down the road
Top