Search results

  1. jimmbo

    Trying to determine proper engine/ trans/ prop pairing

    I would verify that the Tach is accurate-set correctly.
  2. jimmbo

    Trying to determine proper engine/ trans/ prop pairing

    That Velvety Fuzz is a Speed Killer, and needs to be removed.
  3. jimmbo

    Possible purchase of 73 Chrysler cadet

    Our 14 foot Skagit was supposedly only 325lbs for the Boat.
  4. jimmbo

    Possible purchase of 73 Chrysler cadet

    Perhaps the Decimal Point is in the wrong place....
  5. jimmbo

    Possible purchase of 73 Chrysler cadet

    From the 73 Brochure
  6. jimmbo

    Possible purchase of 73 Chrysler cadet

  7. jimmbo

    2013 - 2016 V8 Mustang vs Camaro? Same prices, I love them both

    Would look better in Mazda Red. Actually any Colour other than Black
  8. jimmbo

    2013 - 2016 V8 Mustang vs Camaro? Same prices, I love them both

    No I have no Like of the Mach Mustangs, to me they look like Fecal Matter. As for Pontiac, I have always thought they were the Ugliest of the GM Lines. I especially HATE the Grand Prix. The Only Pontiac that I liked was the 1967, and that was because of the Front End and Tail Lights of that...
  9. jimmbo

    Trying to determine proper engine/ trans/ prop pairing

    According to the Chart provided, the WOT Range for that Engine, was shown as 4800-5200
  10. jimmbo

    1967 Evinrude 6 HP (6702) - Newbie

    I have found a lot of Gunk under 38, even when the rest of the Carb(s) looked Clean.
  11. jimmbo

    2013 - 2016 V8 Mustang vs Camaro? Same prices, I love them both

    The 67 and 68 Notchbacks were the Best Looking Mustangs, Ever. After that they actually looked Stupid. The 2005 - 2010 looked Okay, Inside as well as Outside. The Current Ones are Pathetic inside.
  12. jimmbo

    1967 Evinrude 6 HP (6702) - Newbie

    Depending on what the Solvent is... Some like Lacquer Thinner, while good a dissolving Gum and Varnish, can do a Number on a lot of Plastics. Regardless of the Cleaner, the Float, depending on its Composition, shouldn't be left too Long. BRP Carb Kits will provide all the Parts that need...
  13. jimmbo

    2013 - 2016 V8 Mustang vs Camaro? Same prices, I love them both

    Unfortunately, the End Result is an Increase in Maniacs at the Wheel, going even Faster, cause they are Safer in a Crash, making it more difficult to Cull the Herd of bad/defective Gene Pools...
  14. jimmbo

    Trying to determine proper engine/ trans/ prop pairing

    We will know something once we are told what the WOT Rpm is.
  15. jimmbo

    1967 Evinrude 6 HP (6702) - Newbie

    Above was a Service Manual for up to 64. There quite a few Differences between the pre 1965 5 1/2 and the 1965 and later 6hp.
  16. jimmbo

    Trying to determine proper engine/ trans/ prop pairing

    It "Tops Out at 23", yet you claim you Never went WOT...?
  17. jimmbo

    1967 Evinrude 6 HP (6702) - Newbie

    https://www.marineengine.com/parts/johnson-evinrude-parts.php?year=1967&hp=6&model=CD-24&manufacturer=Johnson&section=CARBURETOR+AND+STARTER+GROUP
  18. jimmbo

    2013 - 2016 V8 Mustang vs Camaro? Same prices, I love them both

    A lot if not most of the Problems is because they are using Control Modules to operate things that used to be hooked to Switches and Knobs. A real PIA to Troubleshoot, and most Techs now just keep changing Parts, and charging for them, until the Problem is fixed, which it may never be... In...
  19. jimmbo

    2013 - 2016 V8 Mustang vs Camaro? Same prices, I love them both

    The Quality is dropping
  20. jimmbo

    1969 85hp starflite, low power and cutting in and out

    If the Gaskets, have "NO SEALER" printed/stamped on them, I will assume the Manufacturers know what they are Doing. But it is your Motor, and Money...
Top