Search results

  1. S

    No fuel being drawn into lower cylinder Johnson 7.5hp

    I think sometimes they leak, not stuck closed, but reeds don't fail often on those little motors. Hand over carb....does it spit gas in your hand? When doing this don't suffocate the motor. Here's a parts drop.....
  2. S

    No fuel being drawn into lower cylinder Johnson 7.5hp

    Am I understanding you correctly? You used a 9.9/15 carb kit for a 7.5? If so, yes it won't run correctly.
  3. S

    1981 Evinrude 35hp tiller conversion kit?

    Very time consuming project....and that's if you don't have stuck bolts.
  4. S

    1981 Evinrude 35hp tiller conversion kit?

    Your motor is a 1981.....the swap is a little complex. Just find a good used tiller motor and sell yours.
  5. S

    1977 Johnson 35 HP 35EL77H-Rectifier and starting battery recommendation?

    There would be three capped off wires somewhere....pretty sure you do not have one.
  6. S

    Need help with remote control Evinrude 9.9 setup

    I always thought it was 91 to 92 but maybe 9.9 is different. I do not believe its for the bump stop in your second picture. First picture I can't read well. In my pictures, the picture where you could see my hand, the area is just behind my pinky. To tell you the truth, id just install and...
  7. S

    1977 Johnson 35 HP 35EL77H-Rectifier and starting battery recommendation?

    Might want to put the fattest guy in the bow with this!
  8. S

    Need help with remote control Evinrude 9.9 setup

    This is a 2000 which basically should be a match to yours other than mines a pull start. The only possible thing I could see is it replaces this screw.
  9. S

    Evinrude Mount Assy needed 5007470

    If your looking for used ones maybe tims outboard service in the mid West or seaway marine located in Lynnwood Washington near Seattle. Seaway is in my backyard and I believe they may have more parts than anyone.
  10. S

    Evinrude Mount Assy needed 5007470

    https://www.boats.net/product/brp/5007470?srsltid=AfmBOoo2IMD5la4OQlGDxiv3E_HTypi3yZLZ5-bYVjWNPhhx_kBNl9_CPAU
  11. S

    1977 Johnson 35 HP 35EL77H-Rectifier and starting battery recommendation?

    Supposedly that won't work so keep us updated on whether it does....or your skipping the charging ability?
  12. S

    Need help with remote control Evinrude 9.9 setup

    This video is informative but doesn't address that screw. I have a newer style 9.9 so I'll peek at it later and try and find the hole it goes in. On the 25 there is a bracket on the water jacket side and then pushes on the timer plate. This video shows you can get a primer instead of of a choke...
  13. S

    1998 Johnson J90TSLECM 90 hp with Jet: leaking water

    Glad you got it resolved.
  14. S

    Need help with remote control Evinrude 9.9 setup

    Purple wire would go to electric choke I believe so you might need to purchase the choke solenoid and linkage. I believe that screw is so you can adjust idle before you hook up the throttle cable. Tiller throttle adjustment must get bypassed I'm assuming. I know where that screw goes on a 25...
  15. S

    Need help with remote control Evinrude 9.9 setup

    This is the adapter kit for the 9.9 rude remote. Is it any of these parts?
  16. S

    Need help with remote control Evinrude 9.9 setup

    Not sure on the screw but the temp set up is everywhere. Here's one but you can get one where the sender just sits on the head and you make a bracket off the water jacket bolt...
  17. S

    25hp Evinrude

    You will want to check your tester....they didn't leave the factory that hi. Edited. I just redid a Johnson 35.... Cut some wire off an old harness for the proper color wires and rewired the powerhead pretty quick. 3 hours or so.
  18. S

    1998 Johnson J90TSLECM 90 hp with Jet: leaking water

    Part 40 and part 10....were these replaced? https://www.marineengine.com/parts/johnson-evinrude-parts.php?year=1998&hp=90&model=E90TSLECM&manufacturer=Evinrude&section=EXHAUST+HOUSING
  19. S

    GLSTA 115 Low rpm idle

    Sorry I don't have enough experience with that motor but if their all equal then that's better. I'm sure someone will come around with their input.
  20. S

    GLSTA 115 Low rpm idle

    If your out that far from spec then something is still wrong. Are your settings different from one side of the engine compared to the other side?
Top