Search results

  1. T

    9.9 evinrude wont idle

    If changing the angle of your motor makes a difference then check your gas tank. You may have water in it.
  2. T

    Evinrude Control Box Issue

    Have you Googled panel mount controls?
  3. T

    35 hp Evinrude

    Hey Doug The starter bracket is headed your way USPS. They said it should get to you in 2 days. Take Care Tim
  4. T

    Johnson Add on electric start

    I don’t think it would have any effect on your adjustment. You still have the same distance from the backside of the bracket to the stator. Maybe the threads were damaged at the start of the so they cut it back rather than retapping the threads.
  5. T

    Johnson Add on electric start

    Looks like that was cut out. Maybe the the end of the adjustment screw was messed up and needed to be shortened.
  6. T

    35 hp Evinrude

    Ok I will take the starter off to save on weight as it will be coming from Massachusetts. I will just put my address in the box and the postage will be on the box so when you get it just send me the money order. A hurricane is headed my way tonight and tomorrow so weather permitting I will...
  7. T

    35 hp Evinrude

    What year is your motor? I have a starter and bracket from an 1985 30hp. Not sure if the starter works. it just a parts motor that I have had laying around. If your interested I could send it your way and you can just send me the postage.
  8. T

    1966 johnson 6hp not running on both cylinders and intermittent spark

    Maybe check you ground connections. they need to be clean and tight. just a thought.
  9. T

    35 hp Evinrude

    Some food for thought. I added a starter to my 02 Johnson 40. My starter bolted right into the the block but some motors will need a bracket. I didn’t have a charging system or deep pockets so I just found a spot for the solenoid and called it a day. I use a solar panel to keep the battery...
  10. T

    1993 tracker pro deep v16

    Agreed with the above. You really only need to push the key for cold starts. By pushing the key you activate the choke. Once it’s warmed up pushing the key will only flood the motor. Try just starting with out the choke and if it won’t fire then push the key. Enjoy
  11. T

    short shaft or longshaft how do i measure my 1979 johnson 35 h p

    I’m sorry but I can’t believe this conversation is still going on. I don’t see that Limy is even in on this topic anymore. Limy is probably out fishing and you guys are still arguing. 😂
  12. T

    New points not gapping, 1957 Johnson 35hp Javelin

    I could be wrong but looking at the adjustment screw if it were turned counter clockwise it may open the points.
  13. T

    New points not gapping, 1957 Johnson 35hp Javelin

    What made you change the points in the first place? Was there a problem? a photo would be helpful as well.
  14. T

    johnson 25hp compression

    You mentioned you replaced the head gasket awhile back. Did you retorque the head bolts after running for awhile? If not you could be leaking by and that could be giving you the low numbers. If it’s been a long while you may need to replace the head gasket again. Lap the head as well while...
  15. T

    primer bulb

    If you have fuel coming out of all 4 carbs then you likely reassembled them incorrectly. Check to be sure the clips for the float needles are hooked up. The needle valve should should move up and down with the float.
  16. T

    primer bulb

    Did you have your carbs apart? It sounds like the floats are sticking open.
  17. T

    Water coming out between power head and lower unit

    Are your water tubs lined up and connected?
  18. T

    1964 big twin electrical gremlin

    make sure your wires aren’t backwards from the battery. No reason for the negative to be fused.
  19. T

    Air intake for a 1974 9.9hp Evinrude

    Great news Now get out of the water.
  20. T

    J30JREE JET

    From what I have read in the past most seam to be rated at the head and roughly 10hp less at the jet. But I’m not 100% sure about that.
Top