Search results

  1. N

    Reeds?

    Okey, try to give it a little bit of throttle when starting.
  2. N

    Reeds?

    Do you give it a little bit throttle (pull the knob and give some throttle) when staring it warm or just idle?
  3. N

    1991 150B force outboard no spark

    Do you have Prestolite ignition system with three blue or black CD modules? Or do you have Mercury Thunderbolt system with one switch box? Normally the CD modules or switch boxes can not be tested from resistance with a VOM. You test for voltage from the stator and triggers to the CD...
  4. N

    Force 40 issues

    Not really hard to pull apart. Just to be careful when pulling the propeller shaft cover. Make a puller for it, do not twist the cover to try to turn the cover a bit and try to pry the cover off with a screw driver at the mounting tabs. Really large risk you brake the tabs.
  5. N

    Reeds?

    WinnerCougar74 what is your starting routine to get it start warm then? Interesting to know!
  6. N

    Force 40 issues

    As you describes and I can not feel and se you engine it sounds like the edges at the clutch dog and/or the gear is worn. BUT hard to give a good advice.
  7. N

    Electronic distributor made a buzzing sound

    Yes that maybe is possible. I also do not know if the triggering of the CD box is when the photo diod in the preamp goes from covered to uncovered from the disc or from uncovered to covered by the window. The troubleshooting says if I do not remember wrong to use a credit card to simulate the...
  8. N

    Electronic distributor made a buzzing sound

    But, but there is no points in the distributor as it has the preamp. The electronic distributor has a disc with 3 windows in your case as it i s a 3- cylinder engine. The disc is running through the preamp and the photo electric diod in the preamp is "reading" the windows and trigger the CD box...
  9. N

    Electronic distributor made a buzzing sound

    Yes, try Bill Kelly and why not Franz Buddenberg at Franz Marine Service. Franz is a Chrysler/Force guru.
  10. N

    Electronic distributor made a buzzing sound

    Okey, do not think a troubleshoot will give any answer. It only cover if you have problem with the ignition. If it works and will sound when you start it up just run it. That is what I would do if it was mine engine. Maybe time to catch up one for spare. The bad think is they are pretty...
  11. N

    Electronic distributor made a buzzing sound

    Never have experience of buzzing sound from the distributor. Do you have the OEM preamp or a preamp from CDI Electronics? Very early Magna Power CD boxes from Delta with the two transistors mounted outside the box and this is when the Magna Power was introduced in 1967-1968 and they were on the...
  12. N

    90hp outboard died suddenly, wouldn't restart

    I am not very familiar with these engines but you maybe have two stop possibilities. Keyswitch to stop (left position of the key) and the stop switch. To rule out if it is problem with the stop circuit you can disconnect the stop wire to the switchbox and check for spark. Looking at my...
  13. N

    90hp outboard died suddenly, wouldn't restart

    This engine suppose to have three ignition coils one for each cylinder. Seams odd if all three coils will go bad at the same time. Check the kill switch, it can fail over the time. When the overboard lanyard key is in place the circuit should be open. When activated it ground out the switchbox...
  14. N

    1955 Evinrude Fleetwin 7.5hp carb kit?

    Fleetwinner the compression numbers are also important. These small engines should be in range 80-120 PSI maybe higher, but most important is that the numbers are close to each other. Not more different than 10-15% is a general rule. They will run with 80PSI but 100PSI or more is preferable...
  15. N

    Reeds?

    WinnerCougar74, do not blow it for a Japanese Yamaha 4-stroker. Handle it with care and do not run the hell out of it. You are doing a historic nostalgic deed to preserve it.
  16. N

    question on the starting a "2 cycle Merc" sticky

    We in the old generation 50 or 60+have the knowledge about carb engines and how you maybe have to start it and troubleshoot in a logical way. . The new generation ???? Sad to discover that we will go to a computer troubleshoot generation that will be a random part changer.
  17. N

    Force 40 issues

    Usually when slipping out of gear the edges at the clutch dog and even the edges at the forward gear are rounded, but what I understand you do not get the LU into forward gear. If the clutch dog is worn and the edges rounded it will go into gear but when under load it will slip out. Try to shift...
  18. N

    Reeds?

    About setting the timing, on these Chrysler and Force engines you just set the timing at WOT. Timing at idle will be what it will be. After the timing at WOT you just set the air/fuel mixture and the idle speed. But if you want check the timing at idle with a timing light. My experience is that...
  19. N

    Reeds?

    My experience is to give some throttle and sometimes some choke even if warm. Have a Mercury Thunderbolt 800 80Hp 1972, same actions with it. Some more throttle and sometimes a short choke. Soo this is no issue for me, but remember every engine is individual. Some need a special route to start...
  20. N

    Reeds?

    As you have removed the carbs and intake manifold I would suggest to do the link and sync as Frank A that is in the top of this forum. With the air/fuel mixture screws at 1 1/8-1 1/2 turn out from seated and the throttle pick up point adjusted right it would fire up in about 5 sec with the...
Top