Search results

  1. N

    Reeds?

    Some light thru the reeds are acceptable but not to large gap. 0,10mm (0,004in) in my opinion is acceptable. Remember that these Chrysler can be bloody hard to start cold, I think Frank A said this years ago. But if you have to crank 2 or 10-15 sec until it start, does that matter? Were the old...
  2. N

    125 Force ignition wiring?

    Check out Mastertech Marine (maxrules.com) they have wiring diagram. Look at technical specification-common wiring diagram and then Chrysler Force diagram. Your colors do not follow the OEM colors. Red-hot 12VDC from battery Green-choke Yellow-start Blue- stop to ground White (2)-stop to CD...
  3. N

    Yamaha 25hp 2stroke outboard

    Looking at the video and it sounds like it is misfiring. Do as 99yam40 suggest, check with a timing light. Also check the sparkplugs for crack in the porcelain, change spark plugs, run it in the dark with the hood off and look for sparks jumping to ground (power head). Take a close look at the...
  4. N

    Force 85 hp control cable questions

    This is a link to a YouTube video how to connect and adjust the remote control. Paste this in your browser or google it and you should be able to see it. Chrysler Outboard Remote Control cable install and adjustment. There are some different remote control boxes but they are similar. Do not know...
  5. N

    90hp outboard died suddenly, wouldn't restart

    The engine need three things to run. 1. Air/fuel mixture (right amount mixture) 2. Compression 3. Spark (at the right time) Troubleshoot these three, start with check for spark which is easy. Pull all three plugs, ground them and have the HT wires connected. Turn the key to start and check for...
  6. N

    90hp outboard died suddenly, wouldn't restart

    You have to check for spark at all three plugs. I sounds like there is no spark. If the stator goes bad you will loose spark at all plugs.
  7. N

    1986 85hp force 856X6L no spark

    Okey, I have one question. How did you split the CD module and how did you remove the insulation putty? I think it is easy to repair the CD module if you manage to remove the putty. The main components in the CD is the capacitors and the SRC transistors/thyristors and I think these two fail...
  8. N

    1986 85hp force 856X6L no spark

    Sounds like you have one output channel at one CD module that is bad. Each CD module has two output channels soo a two cylinder engine need one module, a three cylinder engine need two modules but one channel is not in use and a four cylinder need two modules and use all output channels. Try to...
  9. N

    Reeds?

    I use razor blades, pocket knifes or putty knifes when removing old gaskets at smaller parts. At lager parts/surfaces such as bottom of power head to midleg I use a tool made for removing gasket when restoring car engines. Most important is that the surface is smooth and clean. Some sign of the...
  10. N

    can starter spin fly wheel just fast enough for stator to show power but not trigger the triggers?

    I do not really know the answer of your question but I think if the starter turn the flywheel fast enought to generate power to the CDI modules it will be enought for the triggers too. The trigger voltage has to be 0,5VDC DVA or higher to trigger the CDI modules. The starter has to turn the...
  11. N

    Spanner wrench

    Try Franz Buddenburg at Franz Marine Service. He might have one for sale. I have bought tool for measure lash/play and to shime Chrysler 1 piece LU.
  12. N

    Mercury 80 won't crank with plugs installed

    4 stroker can be filled through a bad float needle if it is carb engine or through a bad injector and an open intake valve. Have hade this kind of issue, but it was a B&S engine on a lawn mover. Especially if it has an over head internal fuel tank (no fuel pump). Crank case was filled with about...
  13. N

    1987 mercury 45hp classic 50 shut off in the middle of running

    I have had that kind of issue with two smaller Mercury. One 9,8Hp 1977, started fine and ran for some minutes then shut down. Put it in a large bucket and force heat to the switch box with a heat gun. Shut down after some minutes. Similar issue with a 20Hp 1976, shut down after avail. Did the...
  14. N

    1987 mercury 45hp classic 50 shut off in the middle of running

    You have to check for spark when it shuts down. The switchbox could fail when getting warm and it loose spark. When getting cold it will work for avail again until it get warm. Have to figure out if it is a spark issue or overheating issue. Seams to be a spark issue as if it is an overheating...
  15. N

    70's PenYan

    Force 115Hp, than I think it is a engine post 1984 and pre 1987. Are the color of it white? Force is a rebanded Chrysler engine, Chrysler had to sell the outboard division in early 1980es. 1984 was the last year with Chrysler name and the outboards was sold to US Marine. The engine is very...
  16. N

    what motors are compatible with the 88 125 force?

    125Hp has 3,312 in bore the 120Hp has 3,375 in bore. Many parts are swappable but such as carbs can be different typs, Walbro or Tillotson brand with different part numbers. Gear cases can be different too with different ratio. If I do not remember wrong the 120Hp only had 2 piece drive shaft...
  17. N

    Fuel for older Evinrude/ Johnson

    matt167 yes I know that the octane value has nothing to do with the age of an engine, but here in Sweden the fuel today is worser than it was in pre 70s, 70s and 80s. My experience is that you have to retard the spark advance with todays fuel to be sure you do not got detonation due to...
  18. N

    Mercury 7.5 HP, 9.8 HP Flywheel P/N question

    Nice, the important thing is that the flywheel is for the right ignition system. Older 7,5 and 9,8Hp used magneto system (no electronic system). Maybe not the 7,5Hp, it was introduced in 1969 or 70 and in this era the electronic system became common on smaller engines. Think the 7,5Hp, 9,8Hp and...
  19. N

    Fuel for older Evinrude/ Johnson

    The engine it self will handle 10% Ethanol gas, but all rubber hoses, fuel pump diaphragm etc parts that are made of or has rubber in it will be affected by the ethanol. All old parts that not are suppose to be in contact ethanol will swell after avail. Rubber parts that not are made to stand by...
  20. N

    I'm stumped, please help. 1996 40HP force outboard

    Check the flywheel key. I think it is shared. Flywheel zero mark at zero mark at the timing plate The top piston should be at TDC. Check with a screw driver.
Top