Search results

  1. N

    Looking for some help

    If he has adjust the timing from 30 to 28 dgr BTDC at WOT and at top plug, the flywheel key is okey. BTW 28 or 30 drg BTDC does not matter, it will start and run with both.
  2. N

    Looking for some help

    When cold engine you have to choke these engines. The choke butterflies have to close completely when engaged. Spray some oil/fuel mixture with a spray bottle into the carbs while cranking. If the timing is right and you have right HT-wire at right spark plug it would start or cough. If not you...
  3. N

    Force 125 throttle cables

    I do not understand your question. "Part you rotate"? You screw the connectors to the cables. The one for the throttle is the longer one and it is spring loaded.
  4. N

    dirty water with oil coming out from the holes in the lower unit

    Yes. it is normal and when you run it in a bucket all residue and oil will stay in the bucket. You will see more smoke when running it in a bucket. Two stroker smokes cause it burns oil and if the ratio oil/fuel is a bit more than 50:1 ..... yes you will see more smoke.
  5. N

    dirty water with oil coming out from the holes in the lower unit

    These holes are for draining the midsection from water. The oil is unburned two stroke oil from the fuel mixture. Two strokers do not burn all oil, especially when idling. Smell at the oil, if it would be gear oil you will feel the different in smell.
  6. N

    1989 4 CYl. trigger old style(prestolite) vs new style(CDI)

    My suggestion is buy a new one, but they are expensive. You never know the status of a used one and it maybe work for a short while then fail. CDI Electronics might have some sort of warrenty.
  7. N

    1999 Force/Merc 75HP 3 Cylinder 2-Stoke Rough Running Issues

    Well, diaphragm or a piston in the primer. OMC has a piston, Force may have a diaphragm. I have never pull one a part. You have to activate and deactivate with the key pushed in. If it leaks through it the engine will run rich that is one of my suggestion to check for at this issue.
  8. N

    1999 Force/Merc 75HP 3 Cylinder 2-Stoke Rough Running Issues

    You mention you have great spark jumping 1/2 in that is good. But when you try to start it and it would not start how does the spark plugs look like? Are they wet or dry? As this engine has a primer solenoid instead of choke butterflies does the primer work as it should? The primer has a...
  9. N

    99 Force 120 Stalls at Idle

    You also have to check the sync between timing and carbs (link and sync, throttle pick up point). There is a sticker in the top of this forum how to check and adjust this. It is from the past Frank A, there is also a youtube video by FrankA about to do the "link and sync".
  10. N

    99 Force 120 Stalls at Idle

    The idle should be set 1200 rpm in drive way on muffs, 7-800 rpm in water. Starting point set the air/fuel mixture screws at 1 1/4 turn out from seated, then fine tune them after the engine is warmed up. Never set them less than 1 turn out from seated. If the air/fuel mixture is set to lean or...
  11. N

    Evinrude 25hp

    Theoretically a good new 12V battery has 13,8V voltage as it contains six cells and each cell has 2,3V voltage. You can read 12,3 or something and up without load at a bad battery. Remember a starter is a dead short for the battery to serve when trying to start. Maybe a bad battery can be used...
  12. N

    Sourcing parts '89 125 HP

    I have read some where at this forum about the blocking diod a couple of times but I do not know when. Have not have any issue myself regarding it but the diods purpose is to block and secure that the CDI boxes not interfering to each other. The CDI boxes produces the output voltage they should...
  13. N

    Leg Length 1989 Force 85HP

    Yes.
  14. N

    Leg Length 1989 Force 85HP

    Transom height 15 in short leg, 20 in long leg and 25 in X-long leg. Your Bayliner Capri is for a long leg or X-long leg.
  15. N

    Sourcing parts '89 125 HP

    Okey, are the CDI boxes new? I think the CDI boxes has a blocking diod inside and the purpose for it is to block the other CDI box from interference. You can switch the CDI boxes and see if the issue moves to cylinder 3 and 4.
  16. N

    Sourcing parts '89 125 HP

    The Force power does it fire twice when hooking up a second battery to the charging system and is it charging lower amps or does it affect the spark at all cylinders? If I do not remember wrong the stator has two or three windings. Two (or one) for charging the capacitors in the CDI boxes and...
  17. N

    Lower unit shift rod wont screw back in

    Look up at Crowley Marine the schematics for your 35R76G. The schematics you have posted is not the same! The one you posted is for a later model. The first two pics are not showing anything but bluuuur.
  18. N

    Gear lube

    I use automotive gear oil EP 80-90W in all cases with no red metal in. Cases that has bronze parts such as bushings etc I use marine gear oil 80-90W. EP gear oils affect the bronze parts and "eat" it up. The most important thing is check the gear case and gear oil for water intrusion and if...
  19. N

    (Chrysler 25 HP 1975) Outboard Motor 257HA

    Non oil coil is to prefer but if you can not get one use one with oil. All 12V ignition coils built to use in battery system will work. Prime side winding 0.5-3.5 Ohms, secondary side about 9-11 kOhms.
  20. N

    what is it with spark plug $$$$

    The only good with these surface gap plugs are you do not need to change them very often. They last for a very long time. Just pull them clean them up and put them back. Doen not matter of brand, NGK, Champion, Bosch or other. This is my experience of them.
Top