Search results

  1. N

    1990 Force 120HP #2 Cyl zero compression and upon opening piston shows damage

    If the carb intake diameter is the same and the main jet has the same size it should fit. You have to check that the throttle rod and the choke rod lines up with the other carb. The new carb is from a earlier Force as the air fuel mixture screw is not siting in an angle but the function is the...
  2. N

    Sourcing parts '89 125 HP

    Thank you The Force power, I did not have that one.
  3. N

    1966 Johnson 20hp won’t idle and makes a stutter sound

    I think on those engines you can not adjust the shift shaft. The shift shaft has a coupler under a cover at the mid leg. Both shift shaft lower and shift shaft intermidiate has a grove where a screw will secure the coupling. If the teeth at the clutch dog or the teeth for clutch dog at forward...
  4. N

    1966 Johnson 20hp won’t idle and makes a stutter sound

    From the video it looks like it is jumping out of gear.
  5. N

    How to wire a kill switch on a '77 Chrysler 135hp?

    Yes, correct and if the lanyard has both a normally closed and a normally open function you should use the function that open up the contact when you pull the lanyard. When i said in series I mean in between. Blue wire at keyswitch to one of the wire at the lanyard and the other wire at lanyard...
  6. N

    150 hp lower unit replacement

    I think it will fit, the numbers are for right lash for the gears. The two piece drive shafts gear case had computer calculated gears and there was no value for the lash. No procedure how to measure the lash, the digits at the gear case give you the information of which forward gear and pinion...
  7. N

    1965 west bend 450 45hp turning over issues.

    Workshops that repair electrical parts for cars will be able to repair the old OEM starter. Generally they will clean it up, clean the armature, check the bushings and replace the brushes. The OB starters are similar to the starters for cars except for the starter solenoid. Are the starter and...
  8. N

    1965 west bend 450 45hp turning over issues.

    Check all wire connections for the starter, check the starter solenoid. Are the new starters good quality starters or cheap chines crap? Old OEM starters would be like new after a rebuild, uncommon old starters are fried and not rebuildable.
  9. N

    Sourcing parts '89 125 HP

    Do not know why there are different part numbers, I assume the bullentins are OEM from factory. From my experience all 3 and 4 cylinder Chryslers had 3,3126 bore std and the pistons 3,312 except for the 135Hp, 140Hp and 115Hp mid and late 70es that had 3,375. I have a 135Hp 1976 and it has...
  10. N

    Sourcing parts '89 125 HP

    Yes, LD ........ L-drive. Std piston bore 1988 125Hp should be 3,312 in, in 1989 or 1990 they introduced the 120Hp and the std piston bore was 3,375 in. I do not think the 125 Hp had 3,375 but maybe the LD had 3,375 bore.
  11. N

    1975 Johnson 25 HP Not Running

    Butterfly against intake manifold is the throttle, the butterfly at the carb intake is the choke butterfly. The throttle need to be a little open when starting, choke butterfly closed when cold start just for some seconds to get fuel up from the carb bowl to the intake. Throttle and timing...
  12. N

    bought a new to me project today. 35 hp, EVINRUDE electric start with controls HAS NO SPARK

    I never suggest to start replacing parts without trouble shoot first. There are multiples of things that can cause a no spark issue. There can also be not only one bad part issue, it can be two or three. I your case as no spark at all it might be a bad stator coil, a bad CDI box or a bad trigger...
  13. N

    Kill switch question

    Scott I think you reversed the function of the NOHC and NCHO in the explanation of the function or do I think backwards?. NOHC normally open when lanyard is in and closes when pulling the lanyard. NCHO normally closed when lanyard is in and opens when pulling the lanyard. Function should be as...
  14. N

    Kill switch question

    You should have a kill switch with a normally open function. It should close the switch when pulling the lanyard. Wire it parallel with the stop function at the key switch and to ground. Black/yellow is the stop wire and you ground it out when killing the engine.
  15. N

    Johnson J4REEA fuel and carb question

    Yes you should always switch off the fuel shut off valve when not using the engine. As the fuel tank is mounting higher than the carb there is always a pressure at the needle valve due to the gravity. BTW The inlet for the fuel at these carbs are at the bottom of the bowl but there is a channel...
  16. N

    bought a new to me project today. 35 hp, EVINRUDE electric start with controls HAS NO SPARK

    Start with disconnecting the black/yellow wire. It is the stop wire. If no spark then you have to check the output voltage from the charging coil and the output voltage from the trigger coil. To read the peak voltage you have to have a DVA VOM or a DVA adapter connected to a regular VOM...
  17. N

    Force clamp screw bolt thread size?

    I am talking about the bolt diameter (threads) not the head size. Do not know the pitch of the threads but I think Scott Danforth is right. Do not know if it is UNC or UNF, but know that earlier Chryslers had both UNC and UNF depending on year.
  18. N

    Force clamp screw bolt thread size?

    I believe that one is larger. 5/8 x11 UNC or maybe 3/4 x ?. I know that smal OMC engines (5,5Hp Evinrude 1963) has screw diameter size 5/8 and 11 threads UNC an in. I have just restored one that missed both screw clamp.
  19. N

    18 hp Johnson no spark

    As said above from racerone and Crosbyman and check if the low tension wires to the points and condensers has good insulation and not squeezed to ground. When you changed the coils did you adjust them so the iron core rim is flush to the mounting lugs. The gap between the iron core and the...
  20. N

    Need help to id the motor

    Nice to see you saved an old OB from recycling. Maintain it well and it will last for a very long time.
Top