Search results

  1. N

    Will a 1977 135hp Chrysler outboard work as a parts motor for my 1974

    What do you mean with LE? Lower end? Yes you can bolt your 1974 power head to the 1977 middleg and lower end.
  2. N

    Will a 1977 135hp Chrysler outboard work as a parts motor for my 1974

    Jerryjerry is right about the LU, they started to use a one piece LU in 1977- 78. In 1975 some of the 135Hp was equiped with the MagnaPower II igniton until 1977. Then they started to use the Prestolite ignition system. Everything else except the LU and maybe the ignition system are swappable...
  3. N

    Force 50 (1988) comes out of water in reverse

    Remy Mac and Roscoe, the reverse lock is not automatic at Force OBs as it is at Mercury OBs. You have to lock and unlock by hand by the handle part 25. The construction of the lock reverse part 28, it will free from the lock bar part 32 if you hit something and allow the engine to flip up. When...
  4. N

    1996 Force 40HP suddenly died, wont start.

    It is the small black fuel tube he is refer to. The primer solenoid system takes fuel from the carb bowl (discolored tube) and spray a small amount of fuel into the engine intake manifold, behind the carb (small black tube). This is instead of a regular choke butterfly system. If the diaphragm...
  5. N

    1989 85hp force outboard no start issues

    There should be a screw with two washers in the hole in the choke lever and it should be threaded into the threaded hole in the carb body casting. Look just to the right of the right red circle just above the carb bottom cowl. Check in a parts diagram for that engine at for example Crowley...
  6. N

    Can't get flywheel off!!

    Do not use that long bolts, try to have the balance puller as close to the crank end as possible. Set the flywheel under some force by tigthen the bolts BUT not to hard, you will strip the threads. Give the center of the puller a hit with a big hammer then it would come loose. If not, heat the...
  7. N

    1989 85hp force outboard no start issues

    This looks like a carburator for an OMC (Johnson/Evinrude) and it is a manual choke.
  8. N

    Let us know how it worked out!

    Redbarron I fully agree with you. If we got feed back, then it would be more easy to suggest how to solve a problem if we know if some suggestion worked out well.
  9. N

    no fire on both plugs

    I have give you some support/ideas in your other thread.
  10. N

    Point setting for 1985 50 hp force

    If it has battery ignition system (it should have battery ignition from your id tag 507X5A) you have to have 12VDC to the coils from the keyswitch (blue wire). The system use 12VDC from battery to supply the ignition system. If no 12VDC........ no spark. The engine stops when you turn of the...
  11. N

    Point setting for 1985 50 hp force

    If it has magneto ignition system it is 020 in and if it has battery ignition system 015 in.
  12. N

    Compatible parts motor

    The distributor ignition system is the older set up from Chrysler engines mid 60:es. Chrysler started with dist. ignition system auto typ and then i late 60:es they improved the system with an electronic CD module triggered by the points. In mid 70:es they put an optical eye (preamp) instead of...
  13. N

    89 force 125 leaking fuel from carbs

    Your issue is the inlet needles do not seal properly. The tiny hole in the brass plug is went holes for the carb and if the needle do not seal fuel will come out through the hole. I would suggest you to pull the carbs apart and clean them out very well with carb clean fluid and compressed air...
  14. N

    Force 85 Control Operation

    Please pics of the remote control. I think there is a push button in the handel center. You push it in and in the same time you push the handel forward then you get only throttle movement for cold start. But it depend which remote control you have. My youngest son has a 1988 Force 85Hp and the...
  15. N

    Float valve needle 1989. 85hp

    Some carbs do have the wire clip/spring attached to the needle and float and some does not. In the carbs with no wire clip the gravitation will handle the needle to open and the float to close. Two days ago I cleaned my youngest sons Chrysler 65Hp 1977. It has twin carbs and there are no wire...
  16. N

    FUEL PUMP orafices: 3/8" vs 5/16" 1996 FORCE 75hp

    I always use 5/16 fuel lines as I am in Sweden it is metric 8 millimeter. The smaller OB use 1/4 fuel lines or 6 millimeter. You can use 5/16, it will be enough but if you want 3/8 you have to check that the clamp will tight and seal around the fitting. Be careful as the inlet cover fitting for...
  17. N

    Tilt trim switch wiring

    Yes, the bowls need to be clean.... no gunk. Read through your thread and seams you have had to clean out the carbs more then one time. I would suggest you to clean out the whole fuel system, from the tank through the fuel line and fuel pump then in to the carbs. Put a clear inline fuel filter...
  18. N

    Tips and advice for repairing outboard head gasket

    From the pics it do not look like it has overheat badly. The power head is not light brown in color, which it normally would be if it has overheat bad. I have never machined a head which has overheat. You can flat it by sanding with fine water sanding paper. Put the water sanding paper at a...
  19. N

    Tips and advice for repairing outboard head gasket

    Check if there are any score in the cylinder walls? If, can you catch it with your finger nails? If no score put a new head gasket and impeller in. Torque the gasket to proper value in a circular patter starting from the middle left bolt and in CW. Do it in three steps of the torque values. If...
  20. N

    Hints for setting idle mix on 1989 Force 85hp

    Thank you The Force power! It was that one I wanted to refer to, not the video. The procedure is to long to wright down every time someone call for how to adjust the carbs.
Top