Search results

  1. M

    Is this a reasonable quote?

    I don’t see a water intake hose in the quote. Suggest you do that while you’re in there. Price is about right. As I used to tell customers, just think of all the money you saved by not doing the yearly maintenance. If you factor that in, it’s only $2000 for this repair.
  2. M

    Paragon to Velvet drive swap

    If you mean the input shaft running in reverse --- yes. But it is using the forward clutch pack. You can't just put a RH prop on the end of the shaft and shift the trans into reverse like you can with a Hurth.
  3. M

    Paragon to Velvet drive swap

    This is not correct for Velvet Drives. they will burn up if you try to run one in reverse at high speeds. I think the biggest problem you will face is engine height. The flywheel forward engines were used to get the engine low in the bilge and keep shaft angle down. If you have to raise the...
  4. M

    VP 4.3 winterization simplification .... sorta

    OH YA ---- so true. The procedure you described is how most quality shops do it since the low permeation fuel lines came out. They are almost impossible to get off without cutting them.
  5. M

    Volvo 300 CR V8 fuel pump problem

    What was the vacuum at full throttle? Did you see any air bubbles in the clear line when preforming the test. It's not bad luck or bad fuel pumps --- you have something wrong. https://forums.iboats.com/threads/how-to-testing-your-boats-fuel-system.278642/
  6. M

    Volvo 300 CR V8 fuel pump problem

    Check how much vacuum there is between the tank and pump while at full throttle. Should be less than 2”.
  7. M

    Volvo Penta Outboard Model 90 ( 9 hp ) Questions

    Many years ago while working at a Volvo dealer, the owner took one of these in for repair. I called Volvo dealer support and they said there was no parts or literature available from them, but gave me 2 phone numbers to dealers that might still have parts. I called the one on the east coast and...
  8. M

    V8-270-C-B Exhaust bellows (hose) replacement

    Workshop Manual 47700210 is the correct exhaust manual supplement for your serial number. Volvo has "updated their website. I'm thinking there are a few bugs to get worked out.
  9. M

    2012 VP 300 C-A Exhaust manifolds getting too hot - DTC 441 & 442

    Great! Thanks for the follow up ---- it's sure to help others.
  10. M

    MAG 350 loses power after 20 minutes, need help

    91-18078 is the tool to check fuel pressure.
  11. M

    V8-270-C-B Exhaust bellows (hose) replacement

    There should be a metal plate on the port side of the flywheel cover. It will be an inch or two below the bottom of the exhaust manifold. Your engine is a 5.7 block so when Volvo started adding catalyst to them they knew they would be switching to the Gen V blocks. So rather than writing a new...
  12. M

    V8-270-C-B Exhaust bellows (hose) replacement

    You didn't post a serial number so I can only take my best guess. Workshop Manual 47700210 is my best guess, it's a supplement to the engine manual and just covers catalytic exhaust manifolds. There are some more parts that need to be replaced, it's not just the gasket. Be very careful with...
  13. M

    2012 VP 300 C-A Exhaust manifolds getting too hot - DTC 441 & 442

    Normally they are close. But one of the screen shots of Diacom you posted showed engine coolant temp 85° and EMWT 224°. So you will need to monitor where the problem is.
  14. M

    2012 VP 300 C-A Exhaust manifolds getting too hot - DTC 441 & 442

    yes
  15. M

    Water in Engine Oil 5.0 Liter MPI 2002

    Might want to read the service bulletin in the first post. https://forums.iboats.com/threads/water-in-your-oil.361825/
  16. M

    2012 VP 300 C-A Exhaust manifolds getting too hot - DTC 441 & 442

    Yes, I would recommend that you hook up Diacom and watch the exhaust temperature and run at higher rpm if temperatures stay ok. Best to be in the water when doing this.
  17. M

    1997 carver 5.7 port engine removal

    I haven’t done a 325, but have pulled a few engines in similar boats. Before trying to remove the rear window/door assembly you should check to see if a replacement is available. They are sometimes very difficult to remove without damage. Some Carvers I could remove the fly bridge and just...
  18. M

    Volvo Penta Knocking

    Remove the serpentine belt and try running it.
  19. M

    Flywheel bolts came apart

    Yes
  20. M

    ECM Swap ? Plug and play ???

    Is this a 256 SSX? That's a "extended V-plane" hull. Notching the transom did a lot of good things for how those boats rode, all of it at the expense of top speed. HP upgrades with this hull isn't really going to do much -- if anything. Sell it and look for a Regal FasTrac or if you're looking...
Top