Search results

  1. Bondo

    No water coming out of the exhaust on muffs

    Ayuh,..... That's not long enough to fill the system, so that the exhaust can expel the used water,....
  2. Bondo

    Mercruiser 120 poor starting

    Ayuh,.... Doesn't the pickup tube unscrew from the tank,..?? If so, remove it, 'n clean it,..... If there's a screen on the end of it, remove it, then make sure the fuel goes through a quality filter, before the fuel pump/ carb,.... No reason to remove the tank 'n clean it, if it's as clean...
  3. Bondo

    454 dies over 1800RPM loaded

    Ayuh,....... 'n there should only be one check-valve, at the tank's outlet,.....
  4. Bondo

    Mercruiser 120 poor starting

    Ayuh,..... Welcome Aboard,...... It sounds like it's running outa gas, so start with the carb,....
  5. Bondo

    Bought a 1998 Ski Ray RB inboard with zz4 motor and AVS2 carb

    Nope, that's a big block carb, the 1409 is perfect for a 350,....
  6. Bondo

    Bought a 1998 Ski Ray RB inboard with zz4 motor and AVS2 carb

    Ayuh,..... A marine carb is very important,..... The Edlebrock 1409 is the perfect choice for that motor,.....
  7. Bondo

    454 dies over 1800RPM loaded

    Ayuh,..... Why not swap the carbs, motor to motor,.....
  8. Bondo

    Volvo penta 5.0gxi 3869255

    Ayuh,...... Have you changed the fuel filter, 'n examined the contents of the old one, for anything but clean fresh gasoline,..?? The backfiring, says it's going lean,.....
  9. Bondo

    454 MPI seawater impeller

    Ayuh,...... Did you use a hose pick to break 'em free from the housing,..??
  10. Bondo

    5.7 Cast Iron Intake Manifold - Salt (‘raw’) Water Cooled

    Ayuh,..... 5, maybe 10 years life span, they usually fail at the manifold to riser joint,..... If you run 'em til they fail, odds are you'll be replacing the motor at the same time,....
  11. Bondo

    Just rebuilt the trim cylinders, now the outdrive won't stay up under load

    Nope, never been there, but my best friend, 'n mentor used to live there, Don S, who unfortunately passed away some years ago,... I donno whether one cylinder would hold it up, under power,.... Test it like Scott said, on the trailer, run it up, then remove one of the down lines, 'n see if it...
  12. Bondo

    Trim pump rebuild

    Ayuh,..... The spilled oil is easier to clean up, outside the boat,.....
  13. Bondo

    Just rebuilt the trim cylinders, now the outdrive won't stay up under load

    Ayuh,...... If yer confident the cylinder seals were installed properly, if could be the check-valve in the pump,.....
  14. Bondo

    Trim pump rebuild

    Ayuh,...... Welcome Aboard,....... What is it doing, or not doing, that leads you to believe it needs to be rebuilt,..??..??
  15. Bondo

    Monster.

    Ayuh,....... That's Alotta motor, for sure,....
  16. Bondo

    New exhaust manifold advice

    Ayuh,..... I once welded up an old Harley block like that,..... I ground it out a good bit, mig'ed in a puddle, ground it out again, mig'ed it some more, 'n did that several times,...... Each time I did it, I got a little more good weld, 'n a little less crap, 'n bubbles,... After several...
  17. Bondo

    New exhaust manifold advice

    Ayuh,...... As noted above, aluminum is easily welded,..... You did say the manifold in question is aluminum,....
  18. Bondo

    Timing check 350 5.7l Carb

    Ayuh,..... There should be printing on that module that says T-bolt IV,.....
  19. Bondo

    Timing check 350 5.7l Carb

    Ayuh,...... No wires to mess with, with the T-bolt IV,.... Just point, 'n shoot with yer timing light,......
  20. Bondo

    Timing check 350 5.7l Carb

    Ayuh,...... Welcome Aboard,...... Is this the T-bolt IV ignition, or T-bolt V ignition,..?? Post the motor serial number if you don't know which ignition,...
Top