Search results

  1. Lou C

    Verado trim cylinder

    Might try on The Hull Truth, that is outboard heaven.
  2. Lou C

    OMC or Yamaha

    It really depends on what year and model for example: the best would be a '94 and newer with the joint venture drive (really the same as a Volvo) and a GM carburated engine. The Ford engines aren't bad if carbureted but the EFI parts and some ignition parts can't be found. So you could wind up...
  3. Lou C

    1996 Four Winns Sundowner with 5.0 Cobra engine and drive

    Well the only way that would work is if the bin was higher than the level of the raw water pump on the engine. The way the cooling system works, when the boat is in the water, hydrostatic pressure forces water up the outdrive water intakes, through the hoses that lead to the pump, because when...
  4. Lou C

    1996 Four Winns Sundowner with 5.0 Cobra engine and drive

    Holley carb is about as simple as it gets. There will be a # on the air horn near there the choke valve is, that number is what you need to get the right kit. A mixture screw on each side of the fuel bowl & the auto choke adjustment is about it. A nice Holley 4 bbl on a Ford 4 bbl cast iron...
  5. Lou C

    Manifolds (Trying to figure out what I am looking at)

    Good catch Ted! Wonder what would happen if you poked that a bit with a small screwdriver or awl? When I bought the remanufactured heads for mine I got them from a place here on Long Island called Machine World. 7 years later & no leaks. I think they were like $ 275 each….
  6. Lou C

    OMC or Yamaha

    You can find most OMC parts, Yamaha sterndrive parts are extremely rare. That said it depends on what OMC you are talking about... Stringers, no one around here will work on them, parts can be found (used from fresh water areas) but they are all so old Cobras, much easier to find common parts...
  7. Lou C

    1996 Four Winns Sundowner with 5.0 Cobra engine and drive

    These, far better than the dual inlet tempo ones, the rubber on those is too stiff to seal.
  8. Lou C

    1996 Four Winns Sundowner with 5.0 Cobra engine and drive

    With the impeller mounted way up on the engine, you need to have tight fitting muffs and good water pressure, remember that the water has rise about 18" to the water hose that goes thru the transom and then about 3-4' forward to the impeller housing. So you can but have to have muffs that fit...
  9. Lou C

    Time for Riser & Manifold > VP or Barr?

    I used that Permatex on mine when I installed them back in ‘17.
  10. Lou C

    Time for Riser & Manifold > VP or Barr?

    When I did mine I carefully used a razor scraper to get the paint off.
  11. Lou C

    1996 Four Winns Sundowner with 5.0 Cobra engine and drive

    Gasoline vapor detector, which is a significant safety risk in inboard gas engines. I'd like to answer your wiring questions but the only diagrams I have in my OMC factory shop manual are for the '88 Cobras, not sure if yours is wired different. I have the wiring diagrams for both the GM and...
  12. Lou C

    1996 Four Winns Sundowner with 5.0 Cobra engine and drive

    The gauge to the left below the speedo is a gas fume detector. Every gas inboard should have one.
  13. Lou C

    1996 Four Winns Sundowner with 5.0 Cobra engine and drive

  14. Lou C

    1996 Four Winns Sundowner with 5.0 Cobra engine and drive

    If you go over to: www.ifourwinns.com There are a few discussions of that all in one dash panel and some of the problems & solutions. Some replaced the whole thing with a custom panel with separate gauges. In my boat the 36 year old Medallion gauges all still work!
  15. Lou C

    How often to replace points ignition?

    I think the last time I changed mine was in 2016 lol. That was the start of the rough running that turned out to be the water in a cyl/blown head gaskets deal that led to the top end overhaul.
  16. Lou C

    How often to replace points ignition?

    I look to see if they are getting really burned if so I run a point file thru them clean with alcohol on a q tip & set timing & dwell. Then check idle speed. If it starts idles & picks up rpm well I keep using them. Only had a bad condenser once.
  17. Lou C

    De-winterize VP 8.1 Gi-J help please

    I have the same brass plugs in mine for years, and yes I use OMC gasket sealer or Permatex Aviation, never had a problem with seizing up.
  18. Lou C

    Bought my first boat to cut, gut and rebuild from bow to stern, including engine. Killed my back and suffered the wrath of the fiberglass demons

    Yep kinda like that. Pricey but less grief
  19. Lou C

    Bought my first boat to cut, gut and rebuild from bow to stern, including engine. Killed my back and suffered the wrath of the fiberglass demons

    It’s a business arrangement like leasing a boat. You pay X amount a year and can use several boats of a certain size each week. You pay membership & gas and they do the maintenance etc. It can be a good deal like car leasing is sometimes but it’s expensive. Good for people with $$ who want to go...
  20. Lou C

    Bought my first boat to cut, gut and rebuild from bow to stern, including engine. Killed my back and suffered the wrath of the fiberglass demons

    sorry to see that you're still dealing with this, that's why I will not ever do another. You have to be really careful with the personal protection equipment. Next boat will be near new. That, or I'm joining the Freedom Boat Club.
View older results
Top