Search results

  1. Scott Danforth

    How Do You Utilize Sliding Rear Window on Your Pickup

    Grew up with sliding rear windows. With a cap, it was always open to pet the dogs, or grab a water from the cooler in the truck bed With the truck camper, is kids climbed in the back often With an open bed, we kept it open for air flow In college, we had people hanging out the rear slider...
  2. Scott Danforth

    Testing thermostat with torch

    You damage the wax pellet
  3. Scott Danforth

    Where to find this fitting for closed cooling exhaust?

    Can make it with https://www.homedepot.com/pep/Everbilt-3-4-in-Copper-Pressure-45-Degree-Fitting-x-Cup-Street-Elbow-C6062HD34/100674317 And https://www.homedepot.com/p/Everbilt-3-4-in-Copper-Pressure-C-x-MPT-Male-Adapter-C604/100345906 Or shop for groco fittings...
  4. Scott Danforth

    Where to find this fitting for closed cooling exhaust?

    3/4 copper pipe to NPT elbow
  5. Scott Danforth

    Cut wire on top of coil pack

    first, that is not a marine connector, that is one of the insulation displacing splices you find at places like walmart. It is not factory, it was added by a prior owner for unknown reasons. I would remove the splice, and i would put heat shrink over the damaged insulation.
  6. Scott Danforth

    Anyone have experience with exterminating Rats?

    look up corn cobb pail trick for catching rats.
  7. Scott Danforth

    Engine cranking not catching

    Wrong. 60 psi if it's Volvo, 43 psi if it's Mercruiser
  8. Scott Danforth

    Do I replace the core plugs when engine is out?

    Still didn't state why you want to change the vore plugs
  9. Scott Danforth

    Engine cranking not catching

    Missing core plug means the motor went through a hard freeze EFI motors need a few sensors to read correctly prior to allowing fuel and ignition
  10. Scott Danforth

    Thread locker for permanent underwater applications

    Been using it for almost 40 years as a thread locker AND gasket maker AND anti-sieze
  11. Scott Danforth

    100+ outboards

    Drop your prices to about $200 for the 9.9 and they should sell
  12. Scott Danforth

    Why are the oldest postings on a thread NOW listed as the newest ?

    the site owners (outside of moderator control) have been under the hood a lot recently. there are a variety of format changes, font changes, main store front changes, etc.
  13. Scott Danforth

    1981 Capri 14 for sale

    You are looking at a 46 year old boat originally manufactured to last 15. You have to assess the condition of the boat today, not how it was made in 1980
  14. Scott Danforth

    Do I replace the core plugs when engine is out?

    cleaning the water jacket is a different mater. often involves pulling the motor and getting on the stand. removing the heads, and with the pan up, chucking an 18" section of steel cable in a cordless drill and probing the casting.
  15. Scott Danforth

    Hardtop project

    My current job has me working with many of the tower and arch companies. the biggest issue is the fatigue cracks that develop in many towers if not properly designed, especially when pounding waves at 70 mph when heading 150 miles out. yes the top will act as a sail panel when on the road...
  16. Scott Danforth

    OEM Exhaust Manifolds Looking for some other info

    you must not understand why risers are used. it is specifically to make sure the top of the elbows are above the static water line so your boat doesnt sink or fill the motor up with water when at rest.
  17. Scott Danforth

    Do I replace the core plugs when engine is out?

    why would you want to change the core plugs? those are either brass or stainless in a marine motor and will outlast the block
  18. Scott Danforth

    Leak into bilge, bellows?

    With any new to you boat, you really should do all the maintenance the prior owner didn't do
  19. Scott Danforth

    Morse controls

    No, a dual helm is different than a single helm
  20. Scott Danforth

    Exhaust Manifold Question

    The factory cast pieces are made so different risers can be used, and different elbows can be used. Changing the style of gasket will allow the change from a raw water cooled system to a heat exchanger. Also, the individual pieces are easier to cast. The picture shows a welded sheet metal...
Top