Search results

  1. Scott06

    Alpha 1 Gen 2 Gimbal Ring

    Leaking is not going to hurt it as it is wet anyways... it will hurt the pin - Nu Wave marine sells Stainless versions. Maybe some others will weigh in but I'd probably run it. Of course if it breaks I'm out of town that week...
  2. Scott06

    Engine oil choice 1984 3.8l

    The only thing I might add is you have a flat tappet cam, some modern oils do not have enough zinc or ZDDP for flat tappet cams as most engines are roller lifters now. Pretty sure Rotella T4 (conventional not sythetic) still does have enough zinc for flat tappets. Not only do a lot of guys...
  3. Scott06

    48 years...

    @Scott Danforth might have some thoughts. Would have the transom plate replaced and made the thickness of the transom mount on the new outboard. have that time into C channel or boxed tubing on sides of motor bath tub to spread the load so be no issue.
  4. Scott06

    Mechanical fuel pump gph question

    a couple of things to verify- Did it ever get above 3500 rpm? What do spark plugs look like? check that throttle blades and choke are fully opening double check firing order compression test verify ignition timing both intial and total advance check fuel pressure
  5. Scott06

    Alpha 1 Gen 2 Gimbal Ring

    If there is no play when torqued to correct (aka manual listed) torque reuse it.. Why are folks saying to replace it?
  6. Scott06

    Alpha 1 Gen 2 Gimbal Ring

    I put put the swivel pin in there and torque the two bolts down put steering arm on swivel pin and see if there is play. From the photo it looks alright to me but can be hard to tell from the keyboard
  7. Scott06

    Alpha One Gen 2 prop shaft seal replacement

    The plot thickens on this one ... Given how much line was stuck in the seals I was concerned that there would be some in the prop shaft roller bearing so I pulled the bearing carrier. The retainer was PITA as I broke my 1/2" drive 18" breaker bar (pissed me off as I had it for years...). A...
  8. Scott06

    Stern Drive, Trilux and Prevale Sprayer

    Been a few years since I used them but i found those spayers basically useless. If you have a compressor get a harbor freight spray gun. Either way you need to thin the paint down
  9. Scott06

    Alpha 1 Gen 2 Drive Shaft Housing, Lower oil seal replacement?

    I use a beam type like this for setting preload on tapered roller bearings relatively affordable. Have had great results swapping ring and pinions Torque Wrenches, 1/4" Square Drive, 0 - 80 in.-lbs. and 0 - 9 NM Torque https://www.mcmaster.com/7181A22
  10. Scott06

    Sierra 18-2619-1 Outdrive Gasket Set

    You can keep asking but you got four or five thumbs up here. Not sure what you are looking for beyond that.
  11. Scott06

    New (2020) Alpha One Gen 2 wont come off

    Not much different. While its good to remove your drive and inspect I certainly don't every year. If you still have an original greasable gimbal and its smooth leave it alone and grease it. Grease coupler inside. I do engine oil, fuel filter and gear lube annually, grease points and my boats...
  12. Scott06

    New (2020) Alpha One Gen 2 wont come off

    The seal behind the gimbal bearing only keeps gimbal bearing grease out of bilge so it is not critical, would not take out a working gimbal bearing to replace it. It may not even be used anymore with the newer peralube (non greasable) gimbal bearings Ok dirt and grease ring from coupler makes...
  13. Scott06

    Sierra 18-2619-1 Outdrive Gasket Set

    Yeah - buy a couple in case you mess one up putting them on. Also keep some hi perf gear lube and a impeller kit on the shelf. A fuel filter doesn't hurt to have laying around either, never know when you will run into some chit, its the middle of summer and an hour drive to the merc dealer.
  14. Scott06

    Recommended oil for 05 Volvo Penta 5.0gxi e

    because sierra is a common aftermarket marine parts supplier and that's what was locally available ... The 5.0 is a small block chevy ... the two filters long and short that Scott references or any aftermarket cross equivalent ( that means there are probably 50-60 different filter part numbers...
  15. Scott06

    New (2020) Alpha One Gen 2 wont come off

    As mentioned would check alignment as possible cause of hard to remove. Sometimes can be tough to differentiate between liquid from gimbal bearing grease and drive lube in bellows. Would pressure test the drive when off. Brown ring looks like grease and water mix. Remember to glue the big...
  16. Scott06

    Sierra 18-2619-1 Outdrive Gasket Set

    Yes the sierra will work fine
  17. Scott06

    New (2020) Alpha One Gen 2 wont come off

    You basically end up pulling the rusty gimbal bearing out with the drive. Would try the 2x4 and and bet it pushes off with the drive
  18. Scott06

    New (2020) Alpha One Gen 2 wont come off

    Yes 2x4 pushing off rams. If gimbal bearing is rusted to the driveshaft can be hard to remove- this can happen if bellows leak water . Can also get seized to coupler but would not expect that given time involved. I think there are a coupler small slots where you can put a big flat head or...
  19. Scott06

    Wires on trim posn sender frayed.

    I was able to reconnect mine and cover with shrink sleeve. Best if you can solder the wires together and then shrink sleeve over or use a low temp solder butt splice
  20. Scott06

    Fogging with 10W30 oil

    Sure this is fine. In the old days I used to squirt oil in through the spark plugs holes and bump the engine with coil disconnected. I also have done nothing some years and that is ok too, the engine will not be damaged if it sits without fogging for a couple months.
Top