Search results

  1. Scott Danforth

    mercruser 888 wont rev past 2000 when in gear in the water

    I was partially joking when it comes to adding HP. However, yes. With the wrong gearing you need more motor (torque). A 671 would be overkill. A Magnuson 122 at 14psi would be plenty
  2. Scott Danforth

    1978 Lund Deep V Hull, bow raising up dangerously high

    Get a tiller extension and move your butt forward
  3. Scott Danforth

    1994 Mercrusier 4.3l engine compatability

    You need a vortec marine intake. All 4.3 exhaust manifolds are the same
  4. Scott Danforth

    1993 Stingray 556 Leak in Bilge

    There are 3 screws on the garboard plug flange. Do you really need a video to show you how to remove screws?
  5. Scott Danforth

    A need to vent moment

    Don't take it personally..... He's a butthead Got pics of your forge?
  6. Scott Danforth

    mercruser 888 wont rev past 2000 when in gear in the water

    Could bolt a 671 on top the motor
  7. Scott Danforth

    2002 5,7 Mercruiser exhaust manifold keeps cracking - 5 times this summer

    Barr is one of the OEM casting houses
  8. Scott Danforth

    mercruser 888 wont rev past 2000 when in gear in the water

    Those are big block ratios. You need a lot more motor to spin that ratio
  9. Scott Danforth

    Designs in or over gelcoat?

    I figured you were talking the cap. Still going to take a weekend plus. For a metal flake hull, that is a weekend alone up to the rub rail
  10. Scott Danforth

    Where is the idle mix adjustment on this carb on a 5.7 350 with Thunderbolt IV?

    Holy dirty spark arrestor batman. that alone should be the first order of business.
  11. Scott Danforth

    Designs in or over gelcoat?

    first, I highly recommend the Duratec 904 additive over using straight gel and gel with wax as it lays down a lot closer to paint than coming out like manure thru a spreader. Gel doesnt like to come out nice without the 904 additive, no mater how you mix it. even then consider sanding often...
  12. Scott Danforth

    2002 5,7 Mercruiser exhaust manifold keeps cracking - 5 times this summer

    switch to getting manifolds from BARR or Osco or Mercruiser.
  13. Scott Danforth

    Wooden Mounting Base with Casters for Mercruiser 4.3L 1992 Engine

    I used a shipping crate and some bits of 2x4. you can see it in this video. its sitting on the legs of the engine hoist which made it easy to lift the whole thing into the back of the truck i have also ran boat motors sitting on an old tire on the ground. you can also run them hanging from...
  14. Scott Danforth

    mercruser 888 wont rev past 2000 when in gear in the water

    What is base timing? What is all in? At what RPM? Verify the ratio. It should be 1.5:1
  15. Scott Danforth

    Advice On Stringer/Transom Repair

    go to the 3rd sticky down at the top of the forums. read links 14, 15, 18, 19, then the others.
  16. Scott Danforth

    Parking boat in driveway

    In my HOA, a parked boat must be behind a fence not visible from the street. lots of interpretation there as well.
  17. Scott Danforth

    mercruser 888 wont rev past 2000 when in gear in the water

    the two SBF firing orders are basically like an SBC/BBC 4/7 cylinder swap. it evens exhaust pulses, bearing loading and fuel distribution and smooths idle a bit. its good for about 5-10hp not enough to stress about unless trying to eek out every last bit of performance however that is the...
  18. Scott Danforth

    280 outdrive bell housing seal and bearing replacement

    first, welcome aboard second, get yourself the factory service manual from Volvo Penta Third, go here and look up current part numbers https://www.volvopenta.com/shop/0 fourth, read this. https://forums.iboats.com/threads/pds-shaft-issues.687012/
  19. Scott Danforth

    1962 Chris Craft Holiday 20’ bucket list resto

    How you doing Mike?
  20. Scott Danforth

    1971 Glastron GT160 Rear Drain Hole Question

    regardless of the motor on the boat, that transom started rotting about a month after the boat first came out. the encapsulation around the lower drain hole is abysmal. regardless if the splashwell drain was there or not. Im with Bondo, a good TOP on that boat (with a good...
Top