Search results

  1. Bondo

    Squeal from rear of Ford 5.8 Cobra SX

    Ayuh,..... Most times, where ever the latest work was done, is the 1st place to look for a problem that just cropped up,...
  2. Bondo

    Squeal from rear of Ford 5.8 Cobra SX

    Ayuh,.... Welcome Aboard,..... Pull the belts, 'n try it,.....
  3. Bondo

    Omc 4.3 diagnosis

    Ayuh,..... Welcome Aboard,..... It's time for some serious Diagnosis, rather than just throwin' parts at it,..... What Kenny mentions is for Diagnosis reasons,.... That's an old boat,.... could be time to rebuild the carb,.... 'n how 'bout the points,..?? are they fresh this year,..??
  4. Bondo

    Volvo Penta starter issues

    Ayuh,.... Welcome Aboard,...... Yer assumptions are correct,..... 8 months is unacceptable, unless it went swimmin',.... To be honest, 99% of starter problems are actually wirin' problems,..... Removin', 'n cleanin' the wirin' ends in the start system is a common cure,.... Startin' at...
  5. Bondo

    1998 17’ Invader

    Ayuh,.... Welcome Aboard,..... Make one,.... Yer not gonna find parts for such an old boat,....
  6. Bondo

    Mercruiser 5.7 ?

    Ayuh,.... Welcome Aboard,..... 2bbl. carb,..?? 4bbl. carb,..?? Efi,..?? Mpi,..??
  7. Bondo

    1995 4.3 liter mercruiser

    Ayuh,.... What I found on my motor is,..... The 2 front bolts are the odd bolts, with nothin' on 'em,.... 'n aft starboard side is 2 more, with the liftin' ring, under the bolt heads,..... the very back one has the cannon plug bracket on it with a nut, the other one is empty,....
  8. Bondo

    early 70's Mercruiser 165hp inline 6 w/ MC-1 drive not going into gear (sometimes)

    Ayuh,...... 2 possibilities come to mind,...... If the controller was failin', I suppose it could somehow find itself in "Throttle Only" mode, but then goes back to normal,..... The other is maybe the lower shift cable is failin',....
  9. Bondo

    Camshaft Replacement on Vortec 4.3L 262

    Ayuh,.... You need a cam that makes power from idle to 5,000rpms,.... Any bigger cam than that, yer gonna have reversion issues, gettin' water sucked into the cylinders,..... 'n it won't make enough power down low, to get onto plane,......
  10. Bondo

    Lost trim gauge and water temp indications

    Well, pull the sender apart on the gimbel housing, 'n look for a problem there,...... If the wires ain't broken, 'n the sender is good, you'll see varying resistance testin' the wires, with an ohm meter, as the drive is lifted or dropped,.....
  11. Bondo

    Won't go in park or reverse. Stuck in forward position

    Ayuh,..... Did you have the control in forward,..?? Did you hold the drive in forward, as you slid it on,..?? My guess is the answer to one of those questions is, Nope,....
  12. Bondo

    Trim stops working

    Ayuh,..... Where was the fuse ya changed,..?? With a test light, see if the trim pump has battery power,....
  13. Bondo

    Lost trim gauge and water temp indications

    Ayuh,..... The one that goes to the gauge,..... :) They look identical,..... one will meter a varying resistance to ground, the other will be a make, or break switch,.... The make, or break is wired in-line with the up trim button, it opens at tilt,.... Start yer inspection outside the...
  14. Bondo

    25 Hp Mariner 2 stroke motor not starting

    Ayuh,..... Welcome Aboard,...... Any burnt wires under the hood, anywhere,..?? Is the burnt up control harness still plugged into the motor,..?? I'll move this to the Mariner forum for ya,....
  15. Bondo

    Trim stops working

    Ayuh,..... Welcome Aboard,...... Whatcha workin' on,..??..??
  16. Bondo

    boat seats

    Ayuh,.... Welcome Aboard,...... Type "Boat Seats" into yer browser, 'n click go,...... Yer probably not gonna find "Searay" seats, but you'll find millions of boat seats to choose from,....
  17. Bondo

    1979 mercruiser 228 shutter valves

    Ayuh,.... Welcome Aboard,.... Donno whether that'll work, or not,.... If ya do it, do it under the rubber coupler(as in behind the rubber, the rubber will seal the holes), as that's where Merc put 'em, when they moved 'em from the bottom of the y-pipe,.....
  18. Bondo

    1995 4.3 liter mercruiser

    Ayuh,..... Welcome Aboard,..... I've got a '94 sittin' on my shop floor right now,.... The 3/8"-16 odd bolts, go in the upper 2 bolt holes holdin' the flywheel cover to the block flange,.... That's where battery ground, 'n the plug wire legs go,.... The valve covers don't use any odd...
  19. Bondo

    Lost trim gauge and water temp indications

    Ayuh,..... For the temp sender, in the t-stat housing, remove the brown wire, the gauge should be zero,..... Ground that wire to the t-stat housing, the gauge should go Full Hot,..... For the trim sender, there's 2 black soft wires coming through the transom housing, just above the drive...
  20. Bondo

    Shifting very difficult

    Naw,.... The lower unit, from the upper,..... Ya probably bent the piece that slides onto the splines of the shaft shaft, in the lower unit,....
Top