Search results

  1. M

    Yamaha 115 4stroke

    If your setup is like my setup was on my old 2 stroke there should be a small pump on the side of the tank in the bilge (sub tank). It's a small square pump that's actually two gears that turn to move the oil. I would check the voltage at the pump while you flip the toggel switch on, you may...
  2. M

    12v Motorguide keeps frying switches.

    Good you found the issue. Is the bolt connecting the neg cable the proper bolt? Maybe it's just the way it looks in the picture but it looks like a screw thru a nut securing the cable.
  3. M

    Bilge Blower Vent Duct

    aluminum absolutely positively DOES conduct electricity
  4. M

    Help Identifying Part and Purpose

    I third the notion that it's the speedo tube.
  5. M

    12v Motorguide keeps frying switches.

    I'm not familiar with the type of switch your dealing with, can you post a pix of one? Two things come to mind. What are the DC current rating of all of the switches? Also are the switches all rated for DC? Also make sure all wire connections are clean, bright and shiny new. Your battery should...
  6. M

    Impeller Failure Help

    If you're unsure of the current condition of the impeller change it out. I've been told by a mechanic to run the motor every once in awhile to keep the impeller wet and flexible and to prevent it from drying out.
  7. M

    12 volt issues

    Hopefully that was your issue and it's fixed. I'd check all the connectors you can get to and clean where necessary and spray some cleaner before reconnecting. https://www.crcindustries.com/products/qd-174-electronic-cleaner-4-5-wt-oz.html
  8. M

    Battery storage in parallel?

    As the other guys said you don't need any wood, concrete is fine. If any of the batteries are the same type/capacity I would connect in parralell and move the charger every couple of months. we don't have basements here on the west coast so I would make sure you have ventilation or just stick...
  9. M

    12 volt issues

    Not the fuse, it's either good or bad. Did you measure the 12 vdc at the ignition switch on the hot side or the switched side? Where did you measured the 3 volts at? Your statement "Its fine right now as i was messing with the wiring at the blower motor switch then had 12.5 volts" tells me you...
  10. M

    12 volt issues

  11. M

    12 volt issues

    If you're measuring the resistance of a fuse as 90 ohms you have issues, it should measure 0. How did you "Notice the voltage at the ignition switch reading 3 volt"? If you measured 3 volts you have an issue. If as you say " Its fine right now as i was messing with the wiring at the blower...
  12. M

    Bleeding trailer surge brake fluid - single handed

    I basically do the same but I start with the passenger side rear first.
  13. M

    Electrical issue, ticking sound

    Does the boat have an engine hour meter? If so it may not be wired thru the ignition switch. Is this a new problem?
  14. M

    Gas Issues

    Are you able to drain that junk out of the tank? What motor is this? Do you use a 10 micron fuel/water filter? Check/clean or replace all fuel filters.
  15. M

    Battery storage

    If you use a maintainer of any kind check the water/acid once in a while to make sure it doesn't boil off during storage.
  16. M

    2007 aqua patio tritoon instrument gauges not working

    When you start checking voltage use the common ground that is connected to the gauges.
  17. M

    Paint Restoration

    Have you tried using regular car wax to buff out a small section to see what it'll do?
  18. M

    2020 Yamaha 90 buzzing

    Glad you found and fixed the problem.
  19. M

    Yamaha or Suzuki Motors.-

    get ready for a ford/chevy debate.
  20. M

    Oil/fuel Question

    What Chris1956 said.
Top