Search results

  1. Bondo

    1984 OMC 3.0 Killswitch Install

    Ayuh,..... Welcome Aboard,...... One of the purple wires goes to the motor's ignition,..... Figure out which one, cut it, 'n wire the kill switch in between the two ends of that wire,....
  2. Bondo

    Boat lift, Shoremaster 3010 (3000lb capacity). Lifting a Reinell 198FNS (3060lbs)

    Ayuh,...... I wouldn't,..... Yer boat weight will be atleast 20% higher after it's gassed up, 'n loaded with toys,.....
  3. Bondo

    Timing indicator

    Ayuh,..... Welcome Aboard,..... To go along with AD, I believe the hot rod shops sell bolt on timin' dedicators too,...
  4. Bondo

    Cracked 5.7 engine

    Ayuh,.... Ditto this,..... Lightly grind the area to expose the clean metal, 'n slather it with yer choice of epoxy,.... Then run 'er til she pukes,....
  5. Bondo

    Volvo Penta sx/Cobra 800 swap

    Ayuh,.....Welcome Aboard,.... Yer question is rather confusin',..... Do you have a busted SX- Cobra in the boat, 'n want to swap in another SX- Cobra,..?? Or,..... Do you have a busted stringer 800 drive, 'n you want to swap in a SX-Cobra,..?? In other words,...... Where does this "800"...
  6. Bondo

    1996 Mercury 115 2 stroke steering cable broke off in tilt tube

    Ayuh,..... Just replace the tilt tube, 'n be done with it,.....
  7. Bondo

    4.3 engine with 5.0 outdrive

    Ayuh,..... The V8 gear ratio will be to high, unless the V6 is runnin' a really tall prop pitch, 'n you can find a really low pitch prop for it,..... Even then it'll be less than ideal,....
  8. Bondo

    Is it the engine coupler that has gone bad?

    Ayuh,.... Welcome Aboard,...... If you smelled burnin' rubber, the steel piece with the splines, has debonded, broke free of the rubber donut it lives in,.... You need a new coupler,..... 'n check the alignment, as that's the usual cause of the failure,....
  9. Bondo

    Air Don't Freeze Winterization

    Ayuh,..... 1st start of the year, Mine takes forever to "See" exhausted water,..... It takes abit to fill the drained block, before it dumps out the back,..... 30, maybe 45 seconds,.... seems like eternity,...
  10. Bondo

    Chevrolet Demon 5,7 l marine engine

    Ayuh,.... Welcome Aboard,...... Where are you gettin' the name Demon,..?? The 350 Chevy is probably the most common boat motor in the world,.....
  11. Bondo

    OMC 4.3 Cobra slow Drip from hose

    Nope,..... I use it all the time, on many, Many things,....
  12. Bondo

    OMC 4.3 Cobra slow Drip from hose

    Ayuh,.... It shouldn't leak,..... Ya might sand the nipple abit to smooth it,.... Is the clamp in good shape,..?? Maybe smear the area with form a gasket #3,....
  13. Bondo

    Cherokee 1990 SF prop

    Ayuh,..... You need to verify yer tach, against a known good shop tach,.... If that motor was truly spinnin' that fast, it would have thrown a fod through the block by now,....
  14. Bondo

    Omc cobra water leak

    Ayuh,.... Welcome Aboard,..... Does yer phone have a camera,..?? It'll fit into Alota places yer head won't,...... ;) Where do you live,..?? How was the boat winterized,..??
  15. Bondo

    port side exhaust elbow over heating.

    Ayuh,..... Water, seeks it's own level 'n flows downhill.... It coulda been dumpin' 99% of it's water to the low side,....
  16. Bondo

    port side exhaust elbow over heating.

    Ayuh,..... It don't take much,.....
  17. Bondo

    Fuel line

    Ayuh,..... The fuel pump threads are 1/4" pipe,..... So you need a fittin' from that, to whatever the hose end is,....
  18. Bondo

    port side exhaust elbow over heating.

    Ayuh,.... Was this problem in the water, or on the wagon,..?? If it was on the wagon, just not bein' dead level can cause such a thing,.... Is there one water hose goin' into the bottom of the manifold, 'n another goin' into the riser elbow,..?? If so, pull those hoses, one at a time, 'n...
  19. Bondo

    1993 omc cobra 4.3L

    Ayuh,..... Just because you put gas in the tank, don't mean the gas is available to the fuel pump,..... There's the dip-tube in the tank, the anti-siphon valve at the elbow on top of the dip-tube, 'n the gas line,.... Any of which could be plugged,..... There also can't be any vacuum leaks...
  20. Bondo

    1984 --5.7 / 260HP camshaft ? REPLACE

    Ayuh,.... You need a cam for the '57- '85 Chevy, but with an Rpm range of Idle to 4800- 5000 rpms,.... Usually sold as a Marine, or RV truck cam,....
Top