Search results

  1. dingbat

    Fuel gauge not working

    Have you done any trouble shooting? Solid state….nothing to break, per say. They either work or nothing at all What brand?
  2. dingbat

    Best water separator

    Probably don’t want to hear this after the fact but……while you have to buy a Mercury or OMC “style” filter head separately, the B32 series filters are sized (threaded) to fit the very popular OEM Mercury (11/16”- 16) and OMC (1”-12) filter heads. Allows you to substitute an OEM filter or...
  3. dingbat

    150 Johnson will not idle

    Ideally you want to check for quality of spark which requires a spark tester.
  4. dingbat

    Prop Contacts Trim Tab Only When In Gear Not Neutral

    Should be using this washer with the Flo-torque hub. https://www.mercruiserparts.com/8354671-thrust-washer Make sure you torque the prop nut to 55 ft. Ibs. Required to fully set the flo-torque insert in the prop.
  5. dingbat

    Is the buddy heater safe?

    Used one of these for years while fishing in the winter
  6. dingbat

    Engine data in wrong position on Axiom 9+ MFD with Volvo Easy Connect NMEA 2000 interface

    https://forum.raymarine.com/showthread.php?tid=5470
  7. dingbat

    Volvo 5.0 OSI-GF Fuel Flow Indication

    https://forum.raymarine.com/showthread.php?tid=5470
  8. dingbat

    Chesapeake Virginia?

    Have not fished the pilings in years. The bridge is a good place for sheephead bu there are better and easier places to catch flounder. Stripers, Cobia, and Drum is all I chase down there. Should be Trout at Lynnhaven
  9. dingbat

    How do I Stop Loosing Bearing Buddys??

    I always did the hub since the casting material is softer. Don’t want to deform the bearing buddy casing
  10. dingbat

    Chesapeake Virginia?

    Yep
  11. dingbat

    Fuel gauge not working

    Bag the 20th century float sensor and replace with reed technology. $60….5 screws and two wire nuts and you done https://www.iboats.com/shop/vdo-reed-switch-fuel-sender-240-33-ohm.html?opt=IB00640178&gclid=EAIaIQobChMI4bX5kIvt-QIVitmzCh1i3QTZEAQYASABEgJT6fD_BwE#ib_size=230mm
  12. dingbat

    Help – Aluminum Stress Crack leak?

    The beauty of metal….you can always grind or cut out and start over ;)
  13. dingbat

    Boat tool box

    I carry a spare prop with hardware, fuel filter with wrench, an extra gallon of 2 stroke oil and my Tow Boat membership card.
  14. dingbat

    Cheap Raised ventilated flooring for storage ares?

    Unless the storage lockers are sealed off from the bilge area, chances are good that most of the moisture problem is coming from condensation in the bilge. Had this issue on my first boat. Even with the plug out, 2-3 days after the fact I still had condensation in the bilge that permeated up...
  15. dingbat

    Prop Contacts Trim Tab Only When In Gear Not Neutral

    What prop and drive? Pretty common for prop changes to require a change of the thrust washer as well
  16. dingbat

    Help – Aluminum Stress Crack leak?

    Ends of cracks should have been drilled and filled with weld Aluminum brazing suxs….should have been TIG welded
  17. dingbat

    HF 1.5w Solar Panel for trickle charge dual battery system?

    1.5w at 12 volts is 0.125 amps. Pretty useless as a battery charger
  18. dingbat

    Figuring out AWG cable size for Dual Battery & wiring?

    I suspect if you sat down and did the actual wire sizing calculations based on actual current, duty cycle (%) and insulation (thermal) rating you could down size the battery cables considerably.
  19. dingbat

    How do I Stop Loosing Bearing Buddys??

    An excessively long or incorrectly installed cooter key will rub on the bore or plunger ( when low on grease) of the BB, walking the BB out of the bore over time. Take a center punch and a ball peen hammer and put three dimples, equally spaced, 1/4” - 3/8” in from the face of the hub. The...
  20. dingbat

    thread wear on prop shaft what is causing it?

    Looks like your typical splined shaft that has been threaded. What am I missing?
Top