Search results

  1. J

    wiring help please

    you have two different threads on the same subject , you should keep them in one thread....
  2. J

    wiring help please

    it can be ...frustrating to sort out for sure. I cleaned up the wiring on my '07 pontoon boat last year and even being wired correctly it was still a lot of work just to clean up the factory job....patience needed... honestly....looking closer at your pics....all the splices and different...
  3. J

    wiring help please

    a rats nest, for sure.....so, if it was my boat, I'd start with using these marine color guides.....sort out what I have as correct.....and re-wire as needed...
  4. J

    1999 Chaparral 2130 SS problem

    fuel filter/filters ?....fuel pick-up?
  5. J

    Main fuse

    Yeah…this is mine, in-line. 07 Lowe pontoon…
  6. J

    re-wiring 1988 bass buggy pontoon, would like some help

    and...for a start...
  7. J

    re-wiring 1988 bass buggy pontoon, would like some help

    I re-wired my '07 lowes pontoon boat last year. It was a rats nest also under the console. I added individual positive and negative buss bars, a battery master switch to feed my individual circuits and added a stereo switch also. Originally, it had only 4 switches, one was an accessory switch...
  8. J

    WOT rpm range

    so, I propped my pontoon boat to operate with people on board and tubing. That results in being able to actually exceed my 6000 rpm upper range when running with just me and girlfriend. But when loaded, I'm in the middle or slightly higher of the 5000 - 6000 recommended range..... I lost about...
  9. J

    Rub Rail Aluminum Replacement?

    look up taco marine......or google pontoon rub rails
  10. J

    Bunks with plastic on top

    not a tip...just say'in
  11. J

    Bunks with plastic on top

    because maybe there aren't any?...I checked out of curiosity, cant find 'em either. you could use roofing nails , which is what my Karavan trailer, from the factory, used......just making a point......and they lasted 16 years....
  12. J

    Bunks with plastic on top

    eh...I'm retired,...lots of time on hand....it's a good ,spring loaded, forward pressure stapler..... most of the force applied to my bunks is front to back when launching the pontoon...and vice veraa..so the ends are stapled....good.. the sides and then there's...this..
  13. J

    Bunks with plastic on top

    oh...staples are maybe 2" apart,...fresh water...pine boards,unpainted
  14. J

    Bunks with plastic on top

    I just re-did my pontoon trailer bunks using standard 2x6's. The top, sides and ends are covered..the bottoms are bare. I used T50, stainless steel, 3/8 and 5/16 size staples because thats what I had on hand. A hand stapler was followed by a hammer to further seat the staples...... I also did my...
  15. J

    opinions ---hub temps

    electric brakes...added last year....
  16. J

    opinions ---hub temps

    yep...I was sure....this is my spare...44649...not 44349, my bad
  17. J

    opinions ---hub temps

    no..never heard or read that anywhere.....so, I'll probably add that to my procedures...... thanks
  18. J

    opinions ---hub temps

    yep...I've repacked and pre-loaded bearings for decades...pretty much use the same procedure...... thanks
  19. J

    opinions ---hub temps

    the right side was more into the sun....the temp. gun's accuracy may be off, I just use it for a reference and to help spot possible issues...it didn't burn my hand but I didn't want to keep my fingers on the hotter ones.... thanks..
  20. J

    opinions ---hub temps

    no, I have not repacked them in over 3 years. I've only towed this distance now, and a once a year 200 mile round trip the past 4 years...... they are timken bearings...not chinese... I will repack before next year ... thanks..
Top