Search results

  1. alldodge

    Volvo Penta 5.0 GXI-E - Won't roll over

    No, it's there to keep excess grease out or bilge and help keep dust out, can be reused Most all the new gimbal bearings are sealed and no longer greased. Check to make sure your bearing has a hole in the race so it can be greased
  2. alldodge

    4.3 runs great for about 30 minutes then bogs, pops won't accelerate

    The jumper doesn't "clear" base timing, it puts it in base timing mode so it can be timed.
  3. alldodge

    Constant 'Two Beeps' from my Four Winns 4.3

    Serial shows 555 ECM The highest failure rate item on your motor is the sea water pressure switch. I'm not saying that's the problem it's just they fail often The pump above is the Trim pump, it raises and lowers the drive. The power steering pump is belt drive and on the front of the...
  4. alldodge

    4.3 runs great for about 30 minutes then bogs, pops won't accelerate

    I merged your 3 threads because they are all about the same thing
  5. alldodge

    Volvo Penta Ignition Switch

    Finding something about anti restart. So is it the new type like Mercruiser which shuts the motor off if you try to restart while it's running? Mercruiser is about $50
  6. alldodge

    please help timing issue is the expected issue help!

    Turn key to start and hold, then with other hand move shifter slightly FWD/REV. If it cranks then is the neutral safety switch in the control If not look for the slave relay on the motor next to the 50 amp breaker. The slave is what jumps the starter
  7. alldodge

    Bravo III Mixing Prop Materials

    That is a stainless 24 pitch
  8. alldodge

    How to wire wiper motor

    Made a search and have been unable to find any instructions or diagrams. Does appear you wired it correct, guess the question is I've seen nothing that tells me it will park
  9. alldodge

    1989 Mercruiser 4.3 LX, Alpha 1 Gen 1 Overheating

    Don't know how to test upper elbow, but lower and place rubber piece between Man and elbow to pressure test lower Man
  10. alldodge

    2008 4.3GL Distributor Hold-Down Screw

    Now that's just out and out BS It's one thing to do this kind of thing during warranty period, but after VP should be "required" to remove and replace with a regular bolt. Previous thread on Iboats shows the hex head to be 5.5MM and not standard 5MM...
  11. alldodge

    Bravo III Mixing Prop Materials

    Welcome Don't know of a B3 prop set front or rear which is made of aluminum, all are SS Merc made what is called XR series (4 blade front, 3 blade rear) but all are SS. It's your drive but that is a $10K+ gamble
  12. alldodge

    Flow reducer in Y Pipe?

    Geezers, don't know who put that together, but never seen anything like it. Don't know what the hose that goes from the top of one Man to the other is even should do. It's not closed cooled, so those hose have no effect. My initial thought is remove and plug the Mans where hoses where...
  13. alldodge

    How to wire wiper motor

    Welcome We're gong to need more then you have a wiper motor. Might have been bought from WM but need to know who manufactured it? Part number, something like that?
  14. alldodge

    Need to check shutters… any tips?

    With soap and a hose pic (Phillips screw drive also works) you can work the boots off and look down the Y to get access. A heat gun can soften them up to make them a bit easier. Agree removing the elbows makes it even easier but it can be done without
  15. alldodge

    2016 Mercruiser 6.2L ECT DTS Axius Cooling System Issue

    I'd like to know more about the exhaust sensor that told the PCM it's to hot Next, have you tried swapping the water pressure sensors?
  16. alldodge

    2005 chapparal 215ssi cuddy..prop?

    Welcome Tell us more about the 5.0 motor? Is it a GXI, GI and any other letters for the model? What is the max RPM you can see at wide open throttle (WOT)? What size and pitch is the prop on the boat now?
  17. alldodge

    2001 Mercruiser 5.0 EFI low RPM, low speed, slight vibration

    Welcome The slight ding on the prop should not cause low power or vibration. It's a new to you boat so need to do some things to figure out what the issue(s) are. What is the motor serial number? Your motor should be able to turn 4800 rpm at WOT. Right now we need to find out why it wont...
  18. alldodge

    Flow reducer in Y Pipe?

    I need to look up the cooling system in order to see how it was manufactured. Your saying riser so I betting your talking about the elbow that sits on top the exhaust manifold. The riser, if you do have one, it sits in between the manifold and the elbow. If your motor has hoses connected to...
  19. alldodge

    Bench Test Power Steering Fluid Cooler

    Depends on the fittings If fittings are NPT thread then find NOT fittings to connect a air compressor to, and block off the other end If there inverted flare can do the same just harder to find the fittings
  20. alldodge

    Flow reducer in Y Pipe?

    Have a complete model like 5.7 GLxxxxx
Top