Search results

  1. Horigan

    Cause for new exhaust bellows failure?

    You should pull the exhaust elbow to confirm there is not excessive rust in the water passages. You should also get a IR temp gun and confirm both elbows are running around 120degF. I'll bet the port side is hotter. You may need new exhaust manifold and elbow on that side.
  2. Horigan

    Livewell pump issue

    I would first confirm you're getting power to the pump, first by checking fuses, then power in and out of the switch. If you're getting power out of the switch, then I would pull the pump and see if there is debris jammed inside and bench test it. If that fails, replace the pump. They don't...
  3. Horigan

    Volvo Penta Cobra SX repair

    I’ve had good luck with boatwrench.com for rebuilt drives. They are easier to reach than freshwater.
  4. Horigan

    Cause for new exhaust bellows failure?

    Sounds like you have an obstruction below the exhaust hose (not a bellows). Your boat may have flappers just below that hose that can fall into the Y-pipe and block exhaust flow. You may be able to fish it out from above, but you probably need to pull the drive to find and extract it from the...
  5. Horigan

    Acceptable trailering?

    If it were me, I would verify the tongue weight at a minimum.
  6. Horigan

    Proper Castle Nut Installation

    If the bearings are correct, I would install another washer or two.
  7. Horigan

    Cobra sx outdrive

    That inspection camera should really help you find it. Another potential source is where the trim sensor wire comes through the transom. There's a rubber grommet on the wire that pushes into the transom from the outside and held in with a clip on the inside. At least that's the case with my...
  8. Horigan

    Water in spark plugs

    Is there water in your oil? Did the oil level increase?
  9. Horigan

    Risers getting very hot

    Is your motor cooled with a half closed system with a heat exchanger and anti-freeze in the block, or is it fully raw water cooled?
  10. Horigan

    Water in spark plugs

    First priority is getting the water out of the oil and cylinders. Change the oil, then run the starter with the spark plugs out and the fuel pump relay pulled. Put a towel over the spark plug holes so water doesn't spray every where. You may want to bring each cylinder up to top dead center...
  11. Horigan

    Water pickup tube

    Drill down in this site for diagrams of your motor/drive to find the part number. Start at Evinrude/Johnson, Stern drives, etc. BRP Parts Catalog
  12. Horigan

    VP Outdrive Oil | Topping up

    Half full is where you want it. Anywhere between low and full is fine. The volume of fluid between low and full is surprisingly small.
  13. Horigan

    How do these manifolds, risers, elbows look? 1998 5.0Gi's

    You're lucky. My manifold and risers looked better than yours, after taking them off due to hydro-locking my engine.
  14. Horigan

    Trailer winch question and tilt question? 1st timer.

    It's generally frowned upon to power load a boat onto a trailer as this can displace the bottom material/gravel past the end of the ramp pavement. You should try to float the boat onto the trailer and winch it in the final distance. If your ramp has plenty of pavement behind where you're...
  15. Horigan

    SX Outdrive | Pivot housing | Spline bolt torque

    My joint venture OMC/Volvo manual (SX-M) says 105-120 ft-lbs.
  16. Horigan

    Four weens 1990 freedom throttle shifter

    You can find OMC part numbers at this site. Drill down through Evinrude/Johnson, then SD accessesories. BPR Parts Catalogs
  17. Horigan

    Why is it still getting hot

    These infrared guns are helpful in diagnosing temperature issues. Aim it at your thermostat housing to confirm it's operating at the rated temperature (140-160F). Aim it at the top of the exhaust elbows to confirm you're getting good flow through each (temps no greater than 120F and fairly...
  18. Horigan

    Advice sought on tackling prop shaft seal on VP Duo Prop

    Your drive is fine after running three hours with milky oil, assuming you use Volvo oil which has additives that maintain lubrication with some water present. In addition to the above comments, you need to inspect the shaft under the seal for seal wear and grooves. I recently replaced both of...
  19. Horigan

    Why is it still getting hot

    Welcome. You need to rephrase your question with some sentences. I can't understand your issue with no punctuation.
  20. Horigan

    SX-M Lower Gear Housing

    You may want to consider getting a remanufactured drive and returning yours back for some core value. I've had good luck with boatwrench.com. The engine question determines the drive ratio. You'll need to get a drive with the same ratio.
Top