Search results

  1. Horigan

    OMC Cobra EFI 5.0L stopped and won’t start again

    When I want to do a quick check for spark, I just pull a spark plug wire, insert a phillips screwdriver into the wire end, hold it near the engine block (1/8"), crank the engine and see if there is a spark between the screw driver shaft and the engine block. Make sure you are only holding the...
  2. Horigan

    Sealing compound for DP-SM / SX lower assy

    I would use Permatex Aviation sealant. https://www.permatex.com/products/gasketing/gasket-sealants/permatex-aviation-form-a-gasket-no-3-sealant-liquid-16-oz/
  3. Horigan

    Trailer repair installed wrong disc actuator on 2 axle drum trailer

    Call Dexter and ask them. The master cylinder piston size is likely different between drum and disc actuators. So the actuator will either run out of travel or won’t generate enough pressure. You could just swap the actuators.
  4. Horigan

    Broken leaf spring

    I spray mine with T9 Boeshield, more for corrosion prevention that lubrication.
  5. Horigan

    Solar Power Installation . . .

    Maybe a wire pulling snake would work better also.
  6. Horigan

    Solar Power Installation . . .

    I would suggest a Victron DC DC charger. You don't need 60A and they are smaller and less expensive. I have this on my 30 foot boat. The Orion Smart version can be configured and controlled with you phone via app and Bluetooth.
  7. Horigan

    Fuel pump not working

    First thing I would check is the fuel pump relay.
  8. Horigan

    5.7 omc no thermostat

    Or meat thermometer...
  9. Horigan

    Reinstall SX M/ What O Rings/gaskets needed?

    Yes, where you drain the oil from. There is an overflow plug next to the shifter. To fill you pump oil in from the drain plug hole and stop when it comes out the overflow plug hole next to the shifter. Make sure the drive is level. The overflow and drain plug share the same size O-ring. The...
  10. Horigan

    Reinstall SX M/ What O Rings/gaskets needed?

    Typical seals to replace on the SX-M for reinstall are the drain plug, overflow, and dipstick O-rings and the D-shaped water O-ring. I'm not aware of a kit. If you're chasing water/air leak, check the plastic fitting on the other side of the D-shaped O-ring port to confirm the plastic nipple...
  11. Horigan

    Grooves on hub spindle

    Had the same issue on my trailer. That grooved area is where the rear seal rides. Research Speedi-sleeve and it will show you how to measure the diameter and what sleeve to buy. Be sure to use a gasket sealant under the sleeve.
  12. Horigan

    Raw Water System Cap Leaking

    Another way (better) to measure exhaust manifold/riser flow is to measure the temperature with an IR gun after getting fully warmed up and running on plane. They should be 110F to 120F, definitely under 140F. If one or both is hotter you have a flow issue. Others may chime in on what the max...
  13. Horigan

    Weight distribution on trailer bunks and rollers?

    What brand of trailer is this? Are the roller brackets mounted directly to the trailer frame or on to a large bracket that is shared with the bunks? I ask because my Calkins trailer has a teeter totter system that balances the load between the center rollers and the bunks. Either way, why...
  14. Horigan

    Source for Ford 5.0 EFI Stbd Exhaust Riser?

    Thanks Lou for the input. Are you implying that non-EFI Ford risers are more plentiful?
  15. Horigan

    Source for Ford 5.0 EFI Stbd Exhaust Riser?

    Thanks @ChrisinPHX, I didn't see that spendy new one. This shortage is making me wonder if I should consider moving to a GM motor with carb.
  16. Horigan

    Source for Ford 5.0 EFI Stbd Exhaust Riser?

    Thanks guys. I have a query out to 2040, but haven't heard back. All the hits I get on my internet/ebay search end up being out of stock. I've had two orders refunded. I'm going with what hopefully is a lightly used manifold/riser combo for now. Would it be beneficial to soak the lightly...
  17. Horigan

    Source for Ford 5.0 EFI Stbd Exhaust Riser?

    I need to replace my starboard exhaust riser and am having a hell of a time finding a new part online. Anybody have a source for a new 3855269 exhaust riser, or a great condition used one?
  18. Horigan

    Water in 4 cylinders

    @kingsfisherman , FYI. I just had a water in cylinder event (failed riser, hydro-locked with starter) and found over a quart of water in the oil. Make sure you change the oil and filter a couple of times, soon.
  19. Horigan

    96 penta 5.0 stuck in safe mode

    SAFE mode is driven by dedicated oil pressure and water temperature switches, not the sensors that drive the gauges. The ECM goes into safe mode when either of these switches goes to open circuit. They are normally grounded at normal operating temperatures/pressures. Find the sensors and...
  20. Horigan

    Pics of my prop hubs and gear oil. First time questions.

    Looking at the pics again, I agree with @dubs283. The gear oil looks normal. The oil is just a bit dirty.
Top