Search results

  1. Lou C

    OMC Cobra Information

    You're welcome! The Four Winns Horizons are nice boats, we have an old H-200 and while it needed a lot of repairs due to prior neglect its in good shape now and still runs well with the original Cobra drive and 4.3 V6. I did replace the cyl heads 4 years ago due to the originals being cracked...
  2. Lou C

    Elbow and exhaust manifold inspection what do you think?

    I use a razor scraper (carefully) on cast iron.
  3. Lou C

    Elbow and exhaust manifold inspection what do you think?

    Yes you must remove all the old gasket material on the manifolds elbows and cylinder heads. After install I like to run the engine up to temp let it cool then retorque with my clicker torque wrench.
  4. Lou C

    OMC Cobra Information

    https://www.holley.com/products/fuel_systems/carburetors/marine_carburetors/parts/0-80402-1 see the curved tube above the choke plate? Yours should look like that. Now I think VP used an adapter to use the 2bbl carb on the standard 4bbl intake. If that's how yours is and that's not a marine...
  5. Lou C

    OMC Cobra Information

    Ok what I saw that I don't like was that someone cobbled up the throttle bracket/cable and connection to the carb. What they did was used the later style bracket (to hold throttle cable retainer) that is for the Vortec intakes where the bolts go straight up and down with the old style intake...
  6. Lou C

    Help find part number of OMC engine

    The gasket between the pivot housing and the outdrive is the same for all dog clutch Cobra drives as is the gimble bearing. The exhaust gasket do you mean between the cyl head and the engine, or between the manifold and the exhaust elbow? You have the log style manifolds so that's how to...
  7. Lou C

    OMC Cobra Information

    PS looking closely, I think this engine has been replaced because by '98 it should have been a Vortec engine with updated cyl heads, but I see the old style 12 bolt intake vs the 8 bolt Vortec one. Not that it matters much, but the Vortec puts out about 25 more HP. As long as it has good...
  8. Lou C

    Elbow and exhaust manifold inspection what do you think?

    Yep they look good, just clean up the sealing surfaces, I like to give mine a brush on coat of Rustoleum paint, because it holds up well in the salt air where my boat lives. I took off my 4 year old Barr manifolds to replace the steering actuator behind the engine and they looked great...
  9. Lou C

    Fluid Changes for Winterizing, Do I Need to?

    If you really put just a few hrs on it you can remove the drain and see what comes out. If its pure gear oil then its probably fine to keep running it but any sign of moisture its worth the $20 to replace 2 qts of gear lube.
  10. Lou C

    OMC Cobra Information

    well what did they mean by that? I'm just wondering why the original cast iron unit was changed since unless you are in salt water they last nearly indefinitely unless the engine wasn't winterized. There is nothing wrong with an aluminum intake as long as it is a marine unit that has brass...
  11. Lou C

    Only 4400 rpms on V6 4.3 2005 19P 3blades

    I’m wondering if the original drive was replaced at some point with one originally intended for a V8? In this case I’d think you might need a 17 or even 15 pitch prop….
  12. Lou C

    Only 4400 rpms on V6 4.3 2005 19P 3blades

    One benefit of the V6 in boats this size is fuel economy; I have found that with the Rochester Quadrajet 4bbl 90% of the time I’m running on the small primaries which give good low speed response and excellent fuel economy. But you still have the top end benefit of the huge secondaries; and the...
  13. Lou C

    Only 4400 rpms on V6 4.3 2005 19P 3blades

    I have a 15.5x15 on mine (1.62:1 drive ratio) and it will pull 5,000 or a bit more even WOT. While this definitely lowers top speed the more important result is that it reduces the strain in the engine every time it has to pull the boat up on plane. I’m willing to sacrifice top speed for better...
  14. Lou C

    OMC Cobra Information

    That's a Chevrolet 5.0 with a Holley 2bbl carb, nothing out of the ordinary about them, but if you anticipate freezing temps you must manually drain all the water out of the engine and exhaust system. There are two drains on the engine block, one on each side, lower midsection area, and each...
  15. Lou C

    Help find part number of OMC engine

    http://www.sterndrive.info/model_numbers.html This might help
  16. Lou C

    Help find part number of OMC engine

    Ok what part(s) do you need, many of them are the same for all years of Cobra production but some are not. OMC identified their products by model # which was for the whole power package (engine transom mount and outdrive) this model # is what you use to buy parts. In addition the drive has a...
  17. Lou C

    Fluid Changes for Winterizing, Do I Need to?

    Very interesing here we have the lemon law, they get 4 tries to fix a problem but there is some interpretation, in that the defect must impair function in some way, so things like minor blemishes or squeaks and rattles don't qualify but water leaks that cause rust, operational problems that...
  18. Lou C

    Help plz, 2002 3.0 mercruiser winterizing question

    now, about that paint job....J/k!
  19. Lou C

    Help plz, 2002 3.0 mercruiser winterizing question

    If you filled the exhaust manifold with AF that’s normal there are idle relief openings on the bottom of the transom mount where water exits when the engine is running. Now if it came out the bilge drain plug hole that might just be spillage.
  20. Lou C

    Fluid Changes for Winterizing, Do I Need to?

    I don’t think a once a year oil change should stress anyone out; keep in mind older carbed engines run cool and rich therefore fuel dilution of the oil is a real issue and this has also been a problem on modern 4 stroke outboards. Despite up to date fuel and ignition systems they run very cool...
Top