Search results

  1. Scott Danforth

    Looking for idea's to hide window screws

    Look at the msds sheet for the primer. And check the sika chart https://usa.sika.com/content/dam/dms/us01/3/pds-cpd-SikaflexSealAdhPrimers-us.pdf
  2. Scott Danforth

    Popped through the intake.

    I think the rev limiter is like 5100 rpm IIRC
  3. Scott Danforth

    Trim/ tilt Volvo dp1?

    Use the factory service manual and trouble shoot what you have. Find what is wrong and repair back to factory
  4. Scott Danforth

    Looking for idea's to hide window screws

    Nothing wrong with sika or 3M or lifecaulk. They are all knife-grade adhesive sealants Sillycone has no place
  5. Scott Danforth

    Prop pitch for 150xp crossflow on pontoon

    not even worth trying on a poontoon. you will probably be in the 18" range with a high-thrust style prop.
  6. Scott Danforth

    Merc 75 4 cylinders, 2 carbs

    ebay, $20 https://www.ebay.com/itm/186096197578
  7. Scott Danforth

    Merc 75 4 cylinders, 2 carbs

    me, I would buy a manual from Merc. https://publications.brunswick.com/ or get a used on off of ebay.
  8. Scott Danforth

    Looking for idea's to hide window screws

    70F = 21C campers are a bit easier to heat than a boat hull. @Sailor96, if you still have condensation and moisture inside the boat after warming it up, you may have trapped moisture in the core material. you will find out when you pull the first window
  9. Scott Danforth

    Someday …

    https://www.nauti-craft.com/ I know a few of the folks on the US build team. Very cool tech
  10. Scott Danforth

    Tohatsu thrust washer

    I have merged the threads. do not start multiple threads on same topic
  11. Scott Danforth

    Someday …

    I think I would want a Nauti-Craft with the wave taming hydraulic suspension system between the hulls and deck
  12. Scott Danforth

    Looking for idea's to hide window screws

    The second pic in post #1 shows core material that looks iffy
  13. Scott Danforth

    Looking for idea's to hide window screws

    I would use butyl tape and calk the seam if there is a flange.
  14. Scott Danforth

    Engine Trolley Stand

    a free wood skid and a 2 x 4. cut the 2x4 into a few 8" lengths, make some risers for the mounts to sit on, rest the oil pan and flywheel housing on the skid. dont over think it. you can run the motor on it. you can move it with a forklift, and if you want, run lag screws into the blocks and...
  15. Scott Danforth

    Looking for idea's to hide window screws

    based on the core rot that Grub pointed out, those windows need to come out, the core rot taken care of, then the windows re-bedded. then worry about trim.
  16. Scott Danforth

    What would cause my FSK16 to not be propelled by my Johnson JW10 3hp?

    is the prop actually turning or are you just seeing exhaust bubbles.
  17. Scott Danforth

    Looking for idea's to hide window screws

    Nip the screws, make a PVC surround trim, cover with your favorite upholstery fabric/vinyl
  18. Scott Danforth

    1977 Merc 500 water in oil

    I would reseal the lower this coming weekend
  19. Scott Danforth

    Fuel water separator and fuel filter on 3L

    If you have that much water, you have a water ingress issue with your fuel system
  20. Scott Danforth

    Fogging with 10W30 oil

    Just pouring oil in the intake means oil is pooled in the intake. Depending on what side of the carb you poured it into, you may have fogged cylinders 1, 4, 6, and 7, or 2, 3, 5, and 8. Putting a few CCs in each cylinder and spinning would do a better job
Top