Search results

  1. N

    Why no kill switch on 1975 15hp Chrysler outboard ?

    ollyolly1964, the same wiring as I deschribe for the 15Hp 1975 at top if this thread.
  2. N

    Force 85 Throttle Control Replacement

    From my experience you can replace the remote control cables with Teleflex, Mores or other brands standard cables with 10-32 ends. The connectors at the engine will fit from the old cables and also the connectors at the remote control. Teleflex, Morse etc cables has 10-32 ends at both ends...
  3. N

    1989 Force Gamefisher shift linkage adjustment

    Nice you got it up and running. I think the issue was the cam dent not in position and the lower shift shaft not adjusted properly. The distinct snap when shifting into gear is just right and you know the shift pin is right in the shift cam.
  4. N

    puzzled 88 85 hp has strong spark on number 2 cylinder and super weak spark on 1,3

    Nice you got it running. Your terminology of the ignition parts confused me. It my have been a little hard to understand. Each CDI box controls two cylinders, it has two output channels. A two cylinder engine need one CDI box, a three cylinder engine need two CDI boxes but only use one output...
  5. N

    So i decided to pull the powerhead off....

    As I mentioned in your other post about this issue you have to measure the output voltage from the stator windings, the triggers and the CDI boxes with a DVA meter. You can use a regular VOM but with a DVA meter or a DVA adapter connected to the VOM you are able to read the peak DC voltage...
  6. N

    60s era 9.9 Chrysler autoelectric outboard model 923

    PM me and I will send you a wiring diagram for this motor or the similar 9,2, 20Hp with autoelectric (dyna starter) starter. I will check in my books and workshop collection which diagram I have. I worked on a 1968 20Hp last autumn and from what I remember there was just a couple of screws and...
  7. N

    60s era 9.9 Chrysler autoelectric outboard model 923

    I think you have blown a fuse or tripped a auto fuse. Have not checked with the wire diagram yet but will look at it later. To remove the dyna start winding and to access the flywheel you have to have a special tool. The winding is fitted to a taper and you need the special tool to get it loose...
  8. N

    1989 Force Gamefisher shift linkage adjustment

    I suppose the LU is the same style as the older Chrysler 9,9-15Hp. I think the lower shift shaft is not adjusted properly if the clutch dog edges and the edge at the gear looks good. The edges should be perpendicular and not rounded. In the workshop manual there is a distance from the split edge...
  9. N

    puzzled 88 85 hp has strong spark on number 2 cylinder and super weak spark on 1,3

    As I mentioned in the other post of this issue you have to either check the output voltage for the triggers, the stator and the CDI boxes with a DVA meter and/or check how far the ignition coils can jump the spark, as raceone suggest. Your bulb spark tester are not a good tool for...
  10. N

    puzzled 88 85 hp has strong spark on number 2 cylinder and super weak spark on 1,3

    Have you measure the stator output to the CDI boxes and the output voltage from the CDI boxes to the coils with a DVA meter?
  11. N

    73 chrysler magnapower motorola CD-unite resistance levels

    If it is the Motorola Magna Power I system with the coil with grooves, part number 345375-1. Prime side resistance 0,2-0,24 Ohm Secondary side resistance 500-570 Ohm.
  12. N

    Chrysler Sea King 9.2hp Water Pump info

    Yes it should be -2 instead of -1. My mistake.
  13. N

    1975 25HP thermostat

    I have two 25Hp right now and have had at least six or seven of them and none of them hav had a thermostat. As jerry says, they made a place for one but did not use one.
  14. N

    Chrysler Sea King 9.2hp Water Pump info

    Maybe that one will fit, but the F429065-1 is for 9,2Hp if you check out Mastertech marine site. To be really sure contact Franz Marine, he will give you the right part number.
  15. N

    Need Points information for Sea King 9.2hp

    I do not have the parts list for this engine but I think the points are the same as for the later small Chrysler engines. It should be F12153-1. When I look at the pic and as you says you have spark but it would not fire maybe back fire I think you flywheel key is shared. The key should set the...
  16. N

    1966 Chrysler 50hp won't steer, missing fuel pump.

    As I said before your engine had the old style fuel pump from factory. The old style is mounted beside the block with a bracket. It is a two stage pump and it is driven from the crank case pulses (vaccum/overpressure) by two hoses. The newer style pump is bolted to the block at a intake port...
  17. N

    1966 Chrysler 50hp won't steer, missing fuel pump.

    Check out Ebay. There are 5-6 old style and 2-3 newer style fuel pumps out there. Search Chrysler outboard fuel pump.
  18. N

    Chrysler 1981 55HP Possible CD problem

    Joe I can not say if the magnetic field is strong enough but as the trigger magnet is smaller and it suppose to generate a low voltage to the CDI box to dump the capacitor voltage, it would not be so strong. I would suggest you to take a closer look at the trigger ring. As the triggers purpose...
  19. N

    1966 Chrysler 50hp won't steer, missing fuel pump.

    About the steering problem try to penetrate more with penetrating oil and warm/heat it up with a propane torch. Try to lobe with new grease through the grease fitting. Do not heat to much, there are plastic bushings for the swivel bracket bearing. It is a PIA to work with stiff steering but be...
  20. N

    Chrysler 1981 55HP Possible CD problem

    0,5 VDC or higher from triggers. 180 VDC or more from stator to CDI box (blue-yellow) connected. Orange and red are output to each coil. No spec. of output from CDI box to coil.
View older results
Top