Search results

  1. JASinIL2006

    Transom rebuild questions

    I used a several pieces of plywood glued together, about 2.5" thick. It worked well, but I did need to pick up a drill bit that was slightly longer than the normal. I figure I still saved about $480 over the jig...
  2. JASinIL2006

    PVC stringers?

    I think in this thread people are equating PVC boards with composite plastic wood deck boards (e.g., Trex) that are often made of recycled plastic bags, sawdust and other stuff. They are not the same products. PVC is very different from Trex, in that PVC isn't as dense/heavy, and it can be...
  3. JASinIL2006

    Removing old water lines

    I agree. Anytime I've tried using razor blades on gel coat, the blade ends up digging into the gel and taking out little divots.
  4. JASinIL2006

    Building a '93 Caravelle 1750 Classic Bowrider

    I'm pretty sure you're the first of us to do that.... NOT!
  5. JASinIL2006

    Floatation Foam in Closed Space

    I think with the two-part urethane foam (like that from US Composites), temp is more of a factor than humidity. I did my foaming when temps were cool, so I heated the cavity to be filled and the hull, to make sure I got good yield of the foam mixture.
  6. JASinIL2006

    PVC stringers?

    I think PVC boards have considerably less strength than wood. I also wonder if the resin in fiberglass would chemically melt the PVC. It might be interesting to experiment with, but I certainly would build a boat around it.
  7. JASinIL2006

    Trailer Tires

    Getting tire covers is really a good idea. For infrequently used tires, UV protection will make them last much longer.
  8. JASinIL2006

    Which Oil??? - Mercruiser Power Trim Pump - SAE J1171 Marine

    When I had that issue (a loose hose fitting on a trim ram), just changing the fluid - repeatedly - in the reservoir was not enough; there was enough water in the system that the new oil kept getting milky and foamy. I eventually purged they entire system (instructions in the service manual) and...
  9. JASinIL2006

    Chips in the gel coat on hull. Is it an issue?

    The kit I bought had tubes of color and instructions for color matching. The resulting color isn't perfect, but it's quite close and since it's below the waterline, who cares?
  10. JASinIL2006

    Best manual stapler for replacing carpet on bunks ?

    I couldn’t get a manual stapler to work. I ended up using a pneumatic one.
  11. JASinIL2006

    Chips in the gel coat on hull. Is it an issue?

    Buy this and repair them yourself. It’s easy! https://www.iboats.com/shop/evercoat-match-n-patch-gelcoat-repair-kit.html
  12. JASinIL2006

    method of joining new wood to existing stringer

    I'm not sure leaving the lip saves you any work, and it might actually make the job harder. Normally, you'd cut/grind the lip away, run the new deck board up to within a 1/2" or so of the hull, and then tab the deck to the hull with 1708. In your case, you'll have to put cleats of some sort...
  13. JASinIL2006

    Floor and Transom Rebuild

    Test fitting everything and doing several dry runs is key when using PB. It's really not bad, and todhunter's suggestions are spot on. You can cool your resin a bit before mixing, too; that will give you a little extra time before it kicks.
  14. JASinIL2006

    method of joining new wood to existing stringer

    I'd want the wood to be structurally sound; unless your going the glass the heck out of it, the wood will provide the structural strength. (My foam-core stringers get their strength from the fiberglass, and that glass is 1/2" thick; that's a lot of laminating if you're going to rely on the glass...
  15. JASinIL2006

    Search for canvas

    I would be amazed if you could find one pre-made. Most likely, you will have to get one custom made at a canvas shop. Do you have the metal frame, or do you need that also? I think the frame would be difficult part to locate or fabricate.
  16. JASinIL2006

    Electronics die when cranking engine

    I used an Add A Battery kit to isolate my starting and house batteries. Before I did so, I'd have to restart my Humminbird fishfinder/GPS everytime I restarted the boat. (A pain in the back end when pulling skiers or kids on the tube.) Connecting the electronics to a different battery completely...
  17. JASinIL2006

    Floor and Transom Rebuild

    Sorry, can't help you there. I used PB to attach my transom. You might check the manufacturer's web site to see if it will bond to fiberglass.
  18. JASinIL2006

    Polyester resin ?

    I'm pretty sure the U.S. Composites 435 laminating resin is also ortho. (They draw a distinction between their isophthalic and orthothalic resins on the polyester resin page.) Poly resin was not easily available to me locally, but what I found regionally was that the cost was the same (or more)...
  19. JASinIL2006

    One solution for adding a ski pylon

    I would not be comfortable using a pylon to pull a tube... a booster ball is pretty good at keeping the tow line out of the water. There’s just too much leverage applied to the pylon mounting point when pulling a tube. Your install is nice and clean, but I’d still be concerned about everything...
  20. JASinIL2006

    Air bags

    Ugh... I meant to say, air bags don’t INCREASE your payload....
Top