Search results

  1. Scott Danforth

    Seafoam vs. Marine Pro Seafoam

    google snake oil
  2. Scott Danforth

    Bellow condition??

    Change them
  3. Scott Danforth

    M9540 24 speed parking brake

    That sucks
  4. Scott Danforth

    225BR hull construction vs. engine size... any differences?

    You have to make test drills into the transom and stringers (from inside the bilge, about 2" up from the inside hull surface) Drill a 5/16" hole about 3/4 deep (8mm x 19deep) and look at the shavings. If the shavings are light colored, dry and smell of fresh cut wood. Seal the holes, you are...
  5. Scott Danforth

    Source/question for a crossmember?

    got a length? googling "bolt on trailer crossmember" brings up a bunch. cold galvanizing (high zinc primer) is common.
  6. Scott Danforth

    Where are the shutoff valves?

    lines could be busted too.
  7. Scott Danforth

    Penta 280 outdrive to mercedes om648

    5-cylinder VW 2.5 liter marine diesels are rated at 165hp. to get to 180, very slight boost in fueling is needed. most of the available electronic tweeks push it over 200hp https://www.ptronic.com/performance-chip-volkswagen-marine-tdi-165-5-165.htm
  8. Scott Danforth

    Penta 280 outdrive to mercedes om648

    bolting the two together is the least of your issues. getting a GM V8 PDS housing for a 280 and the adapter you mentioned.... just money and wrenching the water cooled marine manifold and turbo housing is the hurdle that you need to clear first. the last water cooled one-off manifold that I...
  9. Scott Danforth

    Rev limiter value

    pretty sure the rev limiter in the software is near 5100 RPM. IIRC its a soft limiter on the EFI motors that simply starts cutting spark and fuel by a few cylinders at a time.
  10. Scott Danforth

    Penta 280 outdrive to mercedes om648

    Are there marine exhaust manifolds for the old Mercedes. If not, consider a different motor. Water cooled exhaust and turbos are a must You will need to change the gearing in the drive for a diesel. The AQ130 are Volvo motors. Switching to a GM pattern is a different PDS housing
  11. Scott Danforth

    Search error

    the search function on the forum page is wonky. I have been using google search example: projects other than boats scott danforth site:iboats.com or 4.3 casting numbers scott danforth site:iboats.com or in our case, 1982 Starcraft redneck joe site:iboats.com
  12. Scott Danforth

    Ooo! Sparkly! Redfury's Grinding again!

    welcome back. Im a tad north of you on the scale.....currently on 1000mg B12 supplements to help stave off turning more vintage and chrome than I am. regular use of ibuprofen, aleve, ben-gay creme, heating pad, heated seats, etc. helps with some of the abuse on the body.
  13. Scott Danforth

    2 Stroke Oil Thread

    about 25-30ish years ago, after Dad left Manitowoc Cranes, he worked in the test lab at Tecumseh working on 2-stroke motors for both small outboards, lawn and garden and industrial applications where they were testing various gas/oil ratios. he did the pre-assembly inspection, and did the post...
  14. Scott Danforth

    225BR hull construction vs. engine size... any differences?

    the 5.7 and 5.0 are dimensionally identical. a BBC is a bit wider, and a bit longer, however the motor mounts in the same space the hulls are all pulled the same from the mold these days, I would look long and hard at a 6.2 LS motor before I spent money on a big block. before you go looking...
  15. Scott Danforth

    Mercruiser 350 MAG MPI

    Change the flat cap and rotor. Those things fail often
  16. Scott Danforth

    New Stuff on Vehicles likes/dislikes

    There are a few forums just on swapping LS/LT motors into dead BMWs there are even whole websites selling kits to do most of the work. https://www.sikky.com/product-category/lsx-swap-kits/bmw-kits/
  17. Scott Danforth

    New Stuff on Vehicles likes/dislikes

    thats why I build my daily drivers. my next one will be under 2000#, under 11 ft long, and over 425 hp.
  18. Scott Danforth

    New Stuff on Vehicles likes/dislikes

    Sounds like a solution to a problem that shouldnt exist in the first place, whereas the solution adds significant weight and complexity to an already extremely heavy and overly complex vehicle.
  19. Scott Danforth

    Menards plywood

    the most southern Menards is in Kentucky. so yes, he would be north of Kentucky
  20. Scott Danforth

    Source for bearing buddies rubber plug

    you obviously never seen a dexter hub then. the spindle is hollow, the grease zerk is on the end. you pump grease, it flushes everything out the front cap. you then replace the cap.
Top