Search results

  1. Scott06

    Winterization difficulty

    the outdrive it self in the down position is self draining as long as the drain holes are clear. I spalsh some af in the prop hub to take care of any residual and if you leave it outside you should cover the prop ub so no snow/ice or leaves get in. If you are worried about a new to you boat...
  2. Scott06

    OMC 4.3 V6 dry joint "batwing" conversion exhaust kit

    I think @Lou C did this swap on same engine
  3. Scott06

    Strange exhaust behavior during winterizing

    as bondo mentioned it come up through the manifold bottoms and out the risers. The separate hoses feeding the elbows supply cooling water to the exhaust when the thermostat is not open. This is a warm manifold system vs the cold manifolds with only the supply to the manifolds that is supplied...
  4. Scott06

    My block is drained, right?

    you can always pour some AF in the thermo and it will come out the block drains eventually. After I drain mine then put the plugs back in, take off the hose coming up from the outdrive (at therm hsg), I have a short piece of old cut off radiator hose that has a 90 in it so it points up easy to...
  5. Scott06

    Alpha 1 drive quick question

    is that why the ladies call you 50 cent? Yeah I don't know either. Was assuming they dont just fall out? or did yours corrode?
  6. Scott06

    Alpha 1 drive quick question

    My concern would be if it froze and pushed out the Welch plug I assume you didn’t water test the boat ?
  7. Scott06

    cold weather break in

    When I bought my new GM long block from Michigan motorz a few years back they insisted on rotella T4 conventional 15W40 for break in. Also wanted conventional oil for first 100 hrs before switching to synthetic Your lower temps may play into it but I’d think you’d be fine using it. Long block...
  8. Scott06

    Alpha 1 drive quick question

    Parts breakdown for your upper 3&4 are plugs for that, one is threaded and one Welch plug https://www.marineengine.com/parts/mercruiser-sterndrive-parts/rmralpha-one-transom-assembly-19831990/6216687-thru-0d469858/driveshaft-housing-and-drive-gears
  9. Scott06

    Shift shaft seal / carrier seal / oil o-ring?

    normal this time of year, goes dormant unless someone has a project going. If you dont have it get manual 14 for the gen 2 drive very helpful/good info
  10. Scott06

    Shift shaft seal / carrier seal / oil o-ring?

    do you mean you have lube leaking down the shift shaft in the bellhousing onto the lower ? This may be from the poppet valve in the gear lube line. If you dont pop the drive on quickly any residual lube in the line will leak out when the drive is an inch or so off the bellhousing.
  11. Scott06

    Shift shaft seal / carrier seal / oil o-ring?

    no good deed goes unpunished... On my entire drive the only seal that was somewhat compromised by wear/age was the shift shaft seal. All other seals were in nice shape, except for the prop shaft seal with fishing line... So you had no leaks - just replaced the seals while you were in there?
  12. Scott06

    Shift shaft seal / carrier seal / oil o-ring?

    I tried just replacing the seal on the shift shaft not the whole plastic housing it is in, could never get the seal to to stop leaking , ended up buying the bushing with the seal in it. Sierra is better than most aftermarket parts, but the OEM is best in my experience. My boat is a 2004. two...
  13. Scott06

    Thermostat GLM13230 OEM # 87290A4

    verify the thermostat is opening, would not be the first time a new one didn't work. Put it in a pot of water see what temp it opens at and if it opens fully.
  14. Scott06

    Shift shaft seal / carrier seal / oil o-ring?

    most likely the carrier seal below the water pump. relatively easy to split the drive remove the water pump and pressure test the lower by plugging the hole where the quad ring goes. Usually can clamp a flat piece of metal on it. Get 12-15 psi of air pressure in there and put soapy water on...
  15. Scott06

    Out drive water flow incorrect?

    where it connects to the lower is not what I was talking about. There is a clip farther up the tube that holds it to the bellhousing casting. The clip goes into a 1/4“ hole in the bellhousing , i suspect this where the water is coming out. you will have to look farther up in there than where...
  16. Scott06

    Out drive water flow incorrect?

    its normal. If you look in where the water is coming out behind shift lever, there is a 1/4” hole. There should be a clip that holds the speedo tube in it. With drive up this is open to exhaust cavity which is where the wate4 is coming from
  17. Scott06

    How much water pressure is too much, for running on the hose?

    you must be close to the water tower. Do you get water hammer when the washing machine valve closes? Newer construction will have a reducing station in the house, but what you mention is pretty typical for public water. the 3 homes we have owned on city water have all had 75-90 psi .
  18. Scott06

    How much water pressure is too much, for running on the hose?

    I wouldn’t worry about it any excess will blow out the muffs
  19. Scott06

    Alpha 1 Gen 2 - leak & transom service questions

    if the Y pipe was leaking and you stick a hose in bellhousing the water should go through the engine and leak out the Y pipe, engine running or not. I think the places above the Y pipe that could leak are driveshaft bellows, water in pipe fitting, steering shaft seal. Not sure if shift bellows...
  20. Scott06

    No Spark – 1998 MerCruiser 5.7L Thunderbolt V Ignition

    A lot of folks will use a Delco EST to replace the complete TB system when the module dies due to TB module cost/ lack of availability. The Delco is an OEM quality system and modules when they die are cheaper, although we have seen folks on here getting bad EST modules or having trouble putting...
Top