Search results

  1. alldodge

    Closed cooling through hull valve placement

    I can move it, is it a Merc, VP, other?
  2. alldodge

    Closed cooling through hull valve placement

    Your question has nothing to do with the boat, it has to do with what motor you have
  3. alldodge

    I/O (Sterndrive) Conversion to Outboards

    Hey Ted go look at formula forum, guy could use some inside wife Lifpo4
  4. alldodge

    Glastron soft floor

    Thanks, all good West marine "they are unsure" Your test show issues Me, before E10 even came about I had a small fiberglass tub and put gas in it to clean some parts. The next day it ate right thru and dissolved the bottom Florida marine and tank coats outside of there tanks with epoxy (cost...
  5. alldodge

    Glastron soft floor

    Evidence please
  6. alldodge

    Glastron soft floor

    Resin will add strength to the walls but wouldn't keep it from leaking, need epoxy for that. Gas gets in contact with poly resin it just dissolves it. New aluminum tanks recommend epoxy paint coating on outside.
  7. alldodge

    4.3gl dieseling

    Don't know which GL you have A, B, C ...E
  8. alldodge

    Glastron soft floor

    I wouldn't do that unless your very careful. No more the about 3 psi using a bicycle pump. Getting much above that turns a tank into a bomb If tank comes out and you don't see pitting in the inside or outside IMO your good
  9. alldodge

    Not getting water to crank pumps-Bravo1

    ^^^Agree Intake hose goes on top of belt driven pump You have crank pumps?
  10. alldodge

    Glastron soft floor

    Could be there is nothing wrong with the tank
  11. alldodge

    Glastron soft floor

    Most aluminum tanks are made by Florida marine tank which is now in North Carolina. If it was mine, I would remove the tank just to replace the foam. I'll about guarantee the foam is wet
  12. alldodge

    Glastron soft floor

    BTW first thing you should get is a bunch of PPE You want head to toe with booties and a good full face mask
  13. alldodge

    Rust, generally how to clean and best spray to keep it from rusting?

    Depends if you like taking things apart and cleaning. Some of the wenches are pressed together so taking apart will be a choir. Buying another depends on what you think
  14. alldodge

    Glastron soft floor

    ^^^Agree I've only done it a couple times and use the manufactures sight to make the guess. Don't remember how much I bought for either job I like epoxy (stronger bond) but need to remember when using it there is a given amount of time between coats. Seam to remember it's a about 24 hours. If...
  15. alldodge

    Glastron soft floor

    6lb is required for fuel tank, and boats with no stringers it must use 6 lb Below is me starting with the transom and wound up ripping up a lot more Transom
  16. alldodge

    Glastron soft floor

    Stringers run bow the stern and your saying this is not a stringer that's in the pic
  17. alldodge

    Glastron soft floor

    Does look dry forward, The stringers next to tank look dark, most likely their wet Good progress
  18. alldodge

    Glastron soft floor

    When doing a project like this it can be replaced same as original, or can do it your way. Looking at the angle, I would guess it's just 2 pieces of 1/4 ply and glass. You can decide to use a single piece of ply and go clear to the edge and glass in Your looking at a full gut the further the...
  19. alldodge

    Glastron soft floor

    Agree with you someone did replace the transom, but ..... (yes the but) they didn't replace it correctly. They should have ground the glass off around the edges and then lay layers of glass back on top the wood To get all into doing it mostly right. Rip all the foam out, grid and clean the...
  20. alldodge

    Crank no fuel - oil pressure safety switch ?

    That's the issue, still not getting fuel to the carb
View older results
Top